All categories

2 years ago

What device senses short circuits and stops electrical flow when ground faults occur?.

1 answer:

nataly862011 [7]2 years ago

3 0

A ground-fault circuit interrupter GFCI device senses short circuits and stops electrical flow when ground faults occur.

A ground fault can be described as a fault in electricity where electricity tries to reach the ground from places it was not intended to. The ground-fault circuit interrupter (GFCI) can be described as a device that helps to prevent electrical shocks when a ground fault occurs.

The GFCI works in a way that it has the ability to detect power whenever a device is plugged into it. Whenever a power change or short circuit is detected, the GFCI acts as a circuit breaker and stops the device immediately. In this way, it helps to protect from electrical shocks and protects the device too.

A GFCI is very common to e installed in places that are at a higher risk due to contact with water.

To learn more about ground-fault circuit interrupter (GFCI), click here:

brainly.com/question/7322623

#SPJ4

You might be interested in

Tab stops are very useful when you want to A. align text into rows. B. add space between paragraphs. C. align text into columns.

Alenkasestr [34]

The best answer here is Answer C - Tab stops are useful when you want to "align text into columns".

All tab stops do is shift text a fixed amount to the left or right on the line. They are useful for improving the layout of text when you want to align multiple rows.

Answer A is incorrect because rows are vertical and not horizontal. B is also irrelevant because spaces between paragraphs are vertical. Answer D could also be correct because you can use tab stops to indent text aswell, but the more general answer is A. If you can have more than one answer, you could have A and D.

8 0

3 years ago

Read 2 more answers

The following shared data structures must be declared as global variables such that they are shared by all threads

Elena L [17]

Answer:

what the heck

Explanation:

4 0

3 years ago

Can someone explain to me how to do circuit calculations

GenaCL600 [577]

Use the following rules:

- The sum of currents that enter and exit a node (junction) is always zero. So if you have 3 wires that connect, through one flows 2A, the other 3A, then the third must deliver 5A (taking the direction into account!)

- The sum of voltages across different components should always add up. So if you have a battery of 10V with two unknown resistors, and over one of the resistors is 4V, you know the other one has the remaining 6V.

- With resistors, V=I*R must hold.

With these basic rules you should get a long way!

7 0

3 years ago

Canadian Tire is one of Canada’s largest companies. They operate four large distribution centers service over 470 tire retail ou

olganol [36]

Answer: Provided in the explanation section

Explanation:

A YMS acts an interface between a WMS and TMS.The evaluation system with the key performance indicators are mentioned in the table below.

NOTE: The analysis follows in this order given below

Metric
Description
Comments

Metric 1

Trailer utilization

Description :This captures the status of the trailer whether it is in the yard or is in transit

Comments : Helps in measuring the trailer productivity on a daily ,weekly or monthly basis

Metric 2

Driver utilization

Description : This captures the status of the driver whether the driver is in the yard or is in transit

Comments : Helps in measuring the driver productivity on a periodic basis

Metric 3

Trailer sequence

Description : This captures the order of movement of trailers in the yard on a given day, week or month

Comments : Helps in measuring the order fulfilment efficiency i.e. whether the priority orders have been serviced first or not

Metric 4

Total time in yard

Description : This captures the time spent by the trailer in the yard from the time it enters and leaves the yard

Comments : This helps in measuring the time taken to fulfill a particular request

⇒ Capturing these metrics need inputs from both WMS and TMS, and also the trailers need to have RFID tags attached to them.Then compare these performance metrics with the ones prior to the deployment of YMS to identify the percent gains in the overall operational productivity.

cheers i hope this helped !!

8 0

3 years ago

When Windows deletes the driver package and driver files, in what situation might it not delete driver files used by the device

musickatia [10]

Answer:

when there is no junk

Explanation:

3 0

3 years ago