All categories

3 years ago

How to wire two separate switches & lights using the same power source?

1 answer:

5 0

Pull the other end of each cable through the back of the electrical box for the switch<span> that controls it, then strip the end of the cable with a knife and </span>separate<span> the </span><span>wires.

</span>

You might be interested in

Take any software or Application that you have recently purchased, this can be a video game or any other application helping you

IgorC [24]

A good product should have copyright protection which prevents others from using the product without permission.

Some products specify the penalties which are given to a person who makes unauthorized copies of their product and this is done to clearly educate to avoid ignorance claims.

A good product should have clear lettering which are legible and can be easily read, and should also have reasonable copyright protection.

<h3>What is Copyright?</h3>

This refers to the licensing which is done for a product and is also legally backed which prevents a person from illegally using or redistributing the work of a creator without their explicit consent.

Read more about copyright infringement here:
brainly.com/question/1078532

8 0

2 years ago

a limited-access expressway. A)allows vehicles to enter or exit only at certain place.B) does not permit trucks or buses.C)has n

zepelin [54]

Hello babe I just wanted to say hello

3 0

3 years ago

2. A host computer with an IP address of 172.16.29.155 using a subnet mask of 255.255.255.0 and a gateway of 172.16.29.1 pings a

ASHA 777 [7]

Answer:

From the host IP address and subnet mask, you can tell that both computers are on the same network. Host 172.16.29.155 will need to send an ARP request broadcast for 172.16.29.83 to get the MAC address and update its ARP table if the host 172.16.29.83 has not already done so.

Explanation:

<h2>ADDRESS RESOLUTION PROTOCOL (ARP)</h2>

Address Resolution Protocol (ARP) is a procedure for mapping a logical address known as the IP address to a physical address known as MAC (Media Access Control) address in a local area network. The job of the ARP is essentially to translate 32-bit addresses to 48-bit addresses and vice-versa when using IP Version 4 (IPv4) to communicate on the network.

Most of the computer programs/applications use logical address (IP address) to send/receive messages, however, the actual communication happens over the physical address (MAC address) this happens in the layer 2 of the OSI model. An ARP request is a broadcast, and an ARP response is a Unicast.

Scenarios when ARP is used:

Scenario-1: The sender is a host and wants to send a packet to another host on the same network.

· Use ARP to find another host’s physical address

Scenario -2: The sender is a host and wants to send a packet to another host on another network.

· Sender looks at its routing table.

· Find the IP address of the next-hop (router) for this destination.

· Use ARP to find the router’s physical address

Scenario -3: the sender is a router and received a datagram destined for a host on another network.

· Router checks its routing table.

· Find the IP address of the next router.

· Use ARP to find the next router’s physical address.

Scenario -4: The sender is a router that has received a datagram destined for a host in the same network.

· Use ARP to find this host’s physical address.

The situation in the question above falls under scenario-1. From the host IP address and subnet mask, you can tell that both computers are on the same network. Host 172.16.29.155 will need to send an ARP request broadcast for 172.16.29.83 so to get the MAC address and update its ARP table if the host 172.16.29.83 has not already done so.

7 0

4 years ago

What is the relationship between a folder and a subfolder?

zhannawk [14.2K]

A sub folder is one layer under the folder - hence the prefix sub

3 0

3 years ago

Data in the vendor master are grouped into which three segments? (A) General data, storage data, and purchasing data (B) General

sveticcg [70]

Answer: (E) General data, accounting data and purchasing data

Explanation: Data in the vendor master data collection is the data that describes about the vendors that supply the firms or businesses. The record of the vendors are stored in the database which has subjects like address of vendor, name of vendor etc.

The segments or levels of the vendor master database are general data , purchasing data and the accounting data which gives the information about the good and services that are being supplied by the vendor along with his own details .

Other options are incorrect because inventory data, storage data and pricing data are not found in the data collection of vendor master .thus , the correct option is option(E).

6 0

3 years ago