1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
slava [35]
3 years ago
8

The force that keeps you from sliding on an icy

Engineering
2 answers:
galina1969 [7]3 years ago
6 0

Answer:

Static Friction

Explanation:

To prevent slipping means to prevent the relative motion between the ground and the feet. It is the static friction that opposes the relative motion of the feet with respect to the ground.

oksian1 [2.3K]3 years ago
4 0
Static friction because that keeps you on your feet so you don’t slip
You might be interested in
Approximately how many distributions of Linux are available in different forms and formats? A. 100 B. 200 C. 1,000 D. 2,000
ella [17]

Answer:

C.

Explanation:

I think it’s because it’s the best format

3 0
3 years ago
Two ways in accepting responsibility can help teenagers to maintain coach relations with parents​
Xelga [282]

Answer:

1. It will help the teenagers gain the trust of their parents

2. It will help the teenagers obtain more privileges from their parents.

Explanation:

Responsibility is the state of accepting blame for a particular thing. A teenager who accepts responsibilities owns up to his mistakes and takes control over situations he is assigned to.

When teenagers accept responsibility for their actions, it helps the speaker to gain the trust of his parents who coach him in life. This trust will enable the parents to assign greater privileges to the teenagers because they believe they can handle them. Responsible teenagers do not engage in reckless activities.

3 0
3 years ago
Overshoot for an underdamped system is defined as the maximum displacement of the system at the end of its first half cycle. Wha
Kisachek [45]

Answer:

\zeta =0.69026

Explanation:

We have given no more than 5% overshoot

So maximum overshoot = 5 % =0.05

Maximum overshoot is given by M_P=e^\frac{-\pi \zeta }{\sqrt{1-\zeta ^2}}

Here \zeta is the damping ratio

We know that cos\Theta =\zeta

So \sqrt{1-\zeta ^2}=sin\Theta

So 0.05=e^{-\pi cot\Theta }

ln0.05={-\pi cot\Theta }

0.954={ cot\Theta }

\Theta =46.3485

cos\Theta =0.69026

\zeta =0.69026

4 0
3 years ago
A large building will need several different types of workmen to install and repair pipes for water, heating,
siniylev [52]

Answer:

Plumber and pipefitters

Explanation:

3 0
3 years ago
What is the difference between pound-mass and pound-force?
vichka [17]

Answer:

Pound mass is the unit of mass and which is used in United states customary to describe the mass Slug is also a unit of mass .Pound mass is lbm. But on the other hand pound force is the unit of force.Pound force is lbf.

In SI unit ,the unit of mass is kilogram(kg) and the unit of force is Newton(N)

In CGS system the unit of mass is gram and unit of force is dyne.

8 0
3 years ago
Other questions:
  • Piessunzed water (pin-10 bar, Tin= 1 10°C) enters the hottom of an L 12-m-long vertical tube of diameter D110 mm at a mass flow
    7·1 answer
  • How do you measure 1/8 teaspoon if you<br> only have a 1/4 teaspoon?
    11·2 answers
  • Two-pronged plugs are designed for home use
    11·2 answers
  • A mass of 12 kg saturated refrigerant-134a vapor is contained in a piston-cylinder device at 240 kPa. Now 300 kJ of heat is tran
    8·1 answer
  • A square isothermal chip is of width w = 5 mm on a side and is mounted in a substrate such that its side and back surfaces are w
    7·1 answer
  • An aggregate blend is composed of 65% coarse aggregate by weight (Sp. Cr. 2.635), 36% fine aggregate (Sp. Gr. 2.710), and 5% fil
    5·1 answer
  • PLSSSSS Help !!!!!!!!!!!. It's due today. <br> I will give brainliest to correct answer
    10·2 answers
  • Giving away points hope they help with your questions
    14·1 answer
  • stimate the force required in extruding 70-30 brass at 700C, if the billet diameter is 125 mm and the extrusion ratio is 20
    5·1 answer
  • PLEASE HELP
    12·2 answers
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!