Answer:
people are so confusing nowadays... Mr. Kopin told me to get him a coffee. I'm not his servant!
Explanation: QWERTY Q=P A=L Z=M and the others are what is to the left of them.
A sixteen bit microprocessor chip used in early IBM PCs. The Intel 8088 was a version with an eight-bit externaldata bus.
The Intel 8086 was based on the design of the Intel 8080 <span>and </span>Intel 8085 (it was source compatible with the 8080)with a similar register set, but was expanded to 16 bits. The Bus Interface Unit fed the instruction stream to theExecution Unit through a 6 byte prefetch queue, so fetch and execution were concurrent - a primitive form ofpipelining (8086 instructions varied from 1 to 4 bytes).
It featured four 16-bit general registers, which could also be accessed as eight 8-bit registers, and four 16-bit indexregisters (including the stack pointer). The data registers were often used implicitly by instructions, complicatingregister allocation for temporary values. It featured 64K 8-bit I/O (or 32K 16 bit) ports and fixed vectored interrupts.There were also four segment registers that could be set from index registers.
The segment registers allowed the CPU to access 1 meg of memory in an odd way. Rather than just supplyingmissing bytes, as most segmented processors, the 8086 actually shifted the segment registers left 4 bits and addedit to the address. As a result, segments overlapped, and it was possible to have two pointers with the same valuepoint to two different memory locations, or two pointers with different values pointing to the same location. Mostpeople consider this a brain damaged design.
Although this was largely acceptable for assembly language, where control of the segments was complete (it couldeven be useful then), in higher level languages it caused constant confusion (e.g. near/far pointers). Even worse, thismade expanding the address space to more than 1 meg difficult. A later version, the Intel 80386, expanded thedesign to 32 bits, and "fixed" the segmentation, but required extra modes (suppressing the new features) forcompatibility, and retains the awkward architecture. In fact, with the right assembler, code written for the 8008 canstill be run on the most <span>recent </span>Intel 486.
The Intel 80386 added new op codes in a kludgy fashion similar to the Zilog Z80 and Zilog Z280. The Intel 486added full pipelines, and clock doubling (like <span>the </span>Zilog Z280).
So why did IBM chose the 8086 series when most of the alternatives were so much better? Apparently IBM's own engineers wanted to use the Motorola 68000, and it was used later in the forgotten IBM Instruments 9000 Laboratory Computer, but IBM already had rights to manufacture the 8086, in exchange for giving Intel the rights to its bubble memory<span> designs.</span> Apparently IBM was using 8086s in the IBM Displaywriter word processor.
Other factors were the 8-bit Intel 8088 version, which could use existing Intel 8085-type components, and allowed the computer to be based on a modified 8085 design. 68000 components were not widely available, though it could useMotorola 6800 components to an <span>extent.
</span>
Hope this helps
Since Anil needs to show the overlap of people who live in a certain neighborhood in his city that supports a specific political candidate, the type of conceptual diagram which he should use is a: B: Venn diagram.
<h3>What is a Venn diagram?</h3>
A Venn diagram can be defined as a circular graphical (visual) tool that is typically used for representing, logically comparing and contrasting two (2) or more finite sets of data such as objects, students, events, voters, concepts, people, etc.
In this context, we can reasonably infer and logically deduce that a Venn diagram is a type of conceptual diagram which can be used by Anil in illustrating the overlap of people who are living in a certain neighborhood in his city and supports a specific political candidate in an election.
Read more on Venn diagram here: brainly.com/question/24581814
#SPJ1
Answer:
Explanation:
so why are you doing sign up
Before starting an inboard gasoline engine, you should
remove the engine cover completely to let the engine air out. Next is to change
the fuel filter or the water separator. Marine fuel filters and water
separators help draw water from the boat fuel, therefore protecting the motor
from the water. If water were to get in, it could cause serious problems.
You should also consider changing the engine oil. This is
especially so if the motor boat has been sitting around for a while. The fourth
step is to change the oil filter. It is recommended that the oil filter is
changed every 100 hours or every season. Other steps include;
Recharge the battery.
Refuel your boat.
Check the cooling system.
