1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
shtirl [24]
3 years ago
9

I need calculate the reaction of the supports and calculate Mb, Qb, Nk ​

Engineering
1 answer:
Volgvan3 years ago
3 0

Answer: I have no clue

Explanation:

You might be interested in
In which of the following states would homes most likely have the deepest foundation?
Evgen [1.6K]

Answer:

D) Louisiana, to prevent homes from blowing away in hurricanes.

Explanation:

Louisiana is famous for hurricanes i think that if they were well prepared and had deeper foundation the damage may lower by a good lot.

5 0
3 years ago
Pure butanol is to be fed into a semibatch reactor containing pure ethyl acetate to produce butyl acetate and ethanol. The react
marissa [1.9K]

Answer:

See the pictures attached

Explanation:

All the explanation is given in the pictures

3 0
3 years ago
The moisture content in air (humidity) is measured by weight and expressed in pounds or ____________________.
VikaD [51]

Moisture content is measured in terms of pounds of water per pound of air (lb water/lb air) or grains of water per pound of air (gr. of water/lb air).

Hope this helps❤

3 0
2 years ago
What are some tasks commonly performed in Environmental Service Systems jobs? Check all that apply.
lorasvet [3.4K]

Answer: a,c,d,f

Explanation:

5 0
4 years ago
Rod of steel, 200 mm length reduces its diameter (50 mm) by turning by 2 mm with feed speed 25 mm/min. You are required to calcu
diamong [38]

Answer:

125 cm³/min

Explanation:

The material rate of removal is usually given by the formula

Material Rate of Removal = Radial Depth of Cut * Axial Depth of Cut * Feed Rate, where

Radial Depth of Cut = 25 mm

Axial depth of cut = 200 mm

Feed rate = 25 mm/min

On multiplying all together, we will then have

MRR = 25 mm * 200 mm * 25 mm/min

MRR = 125000 mm³/min

Or we convert it to cm³/min and have

MRR = 125000 mm³/min ÷ 1000

MRR = 125 cm³/min

4 0
3 years ago
Other questions:
  • Air at 35 C, 1 atm, and 50% relative humidity enters a dehumidifier operating at steady state. Saturated moist air and condensat
    13·1 answer
  • A simple ideal Rankine cycle which uses water as the working fluid operates its condenser at 40°C and its boiler at 250°C. Calcu
    15·1 answer
  • The ____________ signal from the robot controller instructs the robot to do something.
    10·1 answer
  • Two kilograms of oxygen fills the cylinder of a piston-cylinder assembly. The initial volume and pressure are 2 m3 and 1 bar, re
    6·2 answers
  • As the porosity of a refractory ceramic brick increases:
    13·1 answer
  • What is a motor and were it goes in. A car
    15·1 answer
  • Which of the following are the main psychological domains?
    7·1 answer
  • A completely mixed activated-sludge plant is being designed for a wastewater flow of 5.0 MGD. The soluble BOD concentration of t
    6·1 answer
  • The Republican National Committee publishes a monthly digest of information for Republicans called .
    15·1 answer
  • How did the Department of Labor identify the interest profiles included in the O*NET Career Tools?
    13·2 answers
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!