1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
Alenkasestr [34]
3 years ago
10

In what way do you think the motorcycles perform work?

Engineering
1 answer:
Svetlanka [38]3 years ago
6 0

Answer:

by the engine

Explanation:

it works pretty much like a car.

You might be interested in
What are the potential hazards relating to materials handling injuries?
const2013 [10]

all 4 apply all these are saftey hazards and must be taken as such anything in a work enviorment should be taken seriously and such as hazard

5 0
3 years ago
The tolerance for a geometric can be easily identified by reading the _________.
baherus [9]

Answer:

C

Explanation:

4 0
3 years ago
Read 2 more answers
A 220-V electric heater has two heating coils that can be switched such that either coil can be used independently or the two ca
Nana76 [90]

Answer:

The resistances of both coils are 131.7 Ω and 29.64 Ω.

Explanation:

Since, there are two coils, they can be used independently or in series or parallel. The power is given as:

Power = P = VI

but, from Ohm's Law:

V = IR

I = V/R

therefore,

P = V²/R

R = V²/P

Hence, the resistance (R) and (P) are inversely proportional. Therefore, the maximum value of resistance will give minimum power, that is, 300 W. And the maximum resistance will be in series arrangement, as in series the total resistance gets higher than, any individual resistance.

Therefore,

Rmax = V²/Pmin = R1 + R2

R1 + R2 = (220 V)²/300 W

R1 + R2 = 161.333 Ω    ______ en (1)

Similarly, the minimum resistance will give maximum power. And the minimum resistance will occur in parallel combination. Because equivalent resistance of parallel combination is less than any individual resistance.

Therefore,

(R1 R2)/(R1 + R2) = (220 V)²/2000 W

using eqn (1), we get:

(R1 R2) / 161.333 Ω = 24.2 Ω

R1 R2 = 3904.266 Ω²

R1 = 3904.266 Ω²/R2  _____ eqn (2)

Using this value of R1 in eqn (1), we get:

3904.266/R2 +R2 = 161.333

(R2)² - 161.333 R2 +3904.266 = 0

Solving this quadratic eqn we get two values of R2 as:

R2 = 131.7 Ω     OR     R2 = 29.64 Ω

when ,we substitute these values in eqn (1) to find R1, we get get the same two values as R2, alternatively. This means that the two coils have these resistance, and the order does not matter.

<u>Therefore, the resistance of both coils are found to be 131.7 Ω and 29.64 Ω</u>

7 0
3 years ago
Various factors to be considered in deciding the factor of safety?
Eduardwww [97]

Answer with Explanation:

There are various factors that needed to be taken into account while deciding the factor of safety some of which are summarized below as:

1) Importance of the structure: When we design any structure different structures have different importance in our society. Take an example of hospital, in case a natural disaster struck's a place the hospital should be the designed to withstand the disaster as it's role in the crisis management following a disaster is well understood. Thus while designing it we need it to have a higher factor of safety against failure when compared to a local building.

2) Errors involved in estimation of strength of materials: when we design any component of any machine or a structure we need to have an exact idea of the behavior of the material and know the value of the strength of the material. But many materials that we use in structure such as concrete in buildings have a very complex behavior and we cannot estimate the strength of the concrete absolutely, thus we tend to decrease the strength of the concrete more if errors involved in the estimation of strength are more to give much safety to the structure.

3) Variability of the loads that may act on the structure: If the loads that act on the structure are highly variable such as earthquake loads amd dynamic loads then we tend to increase the factor of safety while estimating the loads on the structure while designing it.

4) Economic consideration: If our project has abundant funds then we can choose a higher factor of safety while designing the project.

4 0
3 years ago
Public transport is a generic term used to describe the family of transit services available to
Softa [21]

Answer:

true

Explanation:

it is used to describe the family of transit services available to residents of urban area

5 0
3 years ago
Other questions:
  • Differentiate between "Threshold and Resolution" with suitable examples.
    12·1 answer
  • On the first statistics exam, the coefficient of determination between the hours studied and the grade earned was 80%. The stand
    5·1 answer
  • The expression with an AND operator ________ when the expression on its left is false and so it does not evaluate the expression
    11·1 answer
  • What is the output of a system with the transfer function s/(s + 3)^2 and subject to a unit step input at time t = 0?
    5·1 answer
  • A pressurized 2-m-diameter tank of water has a 10-cm-diameter orifice at the bottom where water discharges to the atmosphere. Th
    12·1 answer
  • A spherical interplanetary probe of 0.5-m diameter contains electronics that dissipate 150 W. If the probe surface has an emissi
    11·1 answer
  • What is the condition for sampling frequency to reconstruct the information signal ?​
    8·1 answer
  • Entor" by
    9·1 answer
  • What’s Statistics<br> What are the 2 Source of error in data collection
    14·2 answers
  • Storing parts outside doesn’t cause any environmental risks as long as the items are covered.
    12·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!