All categories

3 years ago

The practice of honoring those who have been lost in battle dates back to which two ancient

Engineering

2 answers:

mel-nik [20]3 years ago

8 0

Indus River valley civilizations I don’t really know anymore on the top of my headache

Serjik [45]3 years ago

3 0

It was between Iranians and filapinons nice work man it’s easy

You might be interested in

Consider a single crystal of nickel oriented such that a tensile stress is applied along a [001] direction. If slip occurs on a

Elena L [17]

Answer:

$\mathbf{\tau_c =5.675 \ MPa}$

Explanation:

Given that:

The direction of the applied tensile stress =[001]

direction of the slip plane = [ $\bar 1$ 01]

normal to the slip plane = [111]

Now, the first thing to do is to calculate the angle between the tensile stress and the slip by using the formula:

$cos \lambda = \Big [\dfrac{d_1d_2+e_1e_2+f_1f_2}{\sqrt{(d_1^2+e_1^2+f_1^2)+(d_2^2+e_2^2+f_2^2) }} \Big]$

where;

$[d_1\ e_1 \ f_1]$ = directional indices for tensile stress

$[d_2 \ e_2 \ f_2]$ = slip direction

replacing their values;

i.e $d_1$ = 0 , $e_1$ = 0 $f_1$ = 1 & $d_2$ = -1 , $e_2$ = 0 , $f_2$ = 1

$cos \lambda = \Big [\dfrac{(0\times -1)+(0\times 0) + (1\times 1) }{\sqrt{(0^2+0^2+1^2)+((-1)^2+0^2+1^2) }} \Big]$

$cos \ \lambda = \dfrac{1}{\sqrt{2}}$

Also, to find the angle $\phi$ between the stress [001] & normal slip plane [111]

Then;

$cos \ \phi = \Big [\dfrac{d_1d_3+e_1e_3+f_1f_3}{\sqrt{(d_1^2+e_1^2+f_1^2)+(d_3^2+e_3^2+f_3^2) }} \Big]$

replacing their values;

i.e $d_1$ = 0 , $e_1$ = 0 $f_1$ = 1 & $d_3$ = 1 , $e_3$ = 1 , $f_3$ = 1

$cos \ \phi= \Big [ \dfrac{ (0 \times 1)+(0 \times 1)+(1 \times 1)} {\sqrt {(0^2+0^2+1^2)+(1^2+1^2 +1^2)} } \Big]$

$cos \phi= \dfrac{1} {\sqrt{3} }$

However, the critical resolved SS(shear stress) $\mathbf{\tau_c}$ can be computed using the formula:

$\tau_c = (\sigma )(cos \phi )(cos \lambda)$

where;

applied tensile stress $\sigma =$ 13.9 MPa

∴

$\tau_c =13.9\times ( \dfrac{1}{\sqrt{2}} )( \dfrac{1}{\sqrt{3}})$

$\mathbf{\tau_c =5.675 \ MPa}$

3 0

3 years ago

Determine the reactor volume (assume a CSTR activated sludge aerobic reactor at steady state) required to treat 5 MGD of domesti

12345 [234]

Answer:

1.0MG

Explanation:

to solve this problem we use this formula

S₀-S/t = ksx --- (1)

the values have been given as

concentration = S₀ = 250mg

effluent concentration = S= 10mg

value of K = 0.04L/day

x = 3000 mg

when we put these values into this equation,

250-10/t = 0.04x10x3000

240/t = 1200

we cross multiply from this stage

240 = 1200t

t = 240/1200

t = 0.2

remember the question says that 5MGD is required to be treated

so the volume would be

v = 0.2x5

= 1.0 MG

4 0

3 years ago

A round bar of chromium steel, (ρ= 7833 kg/m, k =48.9 W/m-K, c =0.115 KJ/kg-K, α=3.91 ×10^-6 m^2/s) emerges from a heat treatmen

Lerok [7]

Answer:

Q = 424523.22 kw

Explanation:

$\rho =7833 kg/m$

k = 48.9 W/m - K

c = 0.115 KJ/kg- K

$\alpha = 3.91*10^{-6} m^2/s$

$T_s = 285 degree celcius$

T_∞ = 35 degree celcius

velocity of air stream = 15 m/s

D = 40 cm

L = 200 cm

mass flow rate $\dot m = \rho AV = 7833 *\frac{\pi}{4} 0.4^2*15$

$\dot m = 14764.85 kg/s$

$A_s = \pi DL = \pi 0.4*2 = 2.513 m^2$

$Q = \dot m C \Delta T = h A_s \Delta T$

$\dot m C \Delta T = h A_s \Delta T$

solving for h

$h = \frac{14764.85*0.115*(285-35)}{2.513*(285-35)}$

h = 675.6 kw/m^2K

$Q = h A_s\Delta T$

Q = 675.6*2.513*(285-35)

Q = 424523.22 kw

7 0

3 years ago

Emergency plans are being formulated so that rapid action can be taken in the event of an equipment failure. It is predicted tha

chubhunter [2.5K]

Answer:

Ammonia gas a hazardous gas to our health, when we are exposed to it for a long time. The gas is lighter than air, that means it's high concentration may not be noticed at the point of leakage, because it flows with the wind direction. Ammonia gas detector are used to determine the concentration of the gas at a particular place. We can use the dispersion modelling software program to know the exact position, where we can place the gas detector, which would be where evacuation is needed.

During evacuation, when the concentration of the gas has increased, a self-contained breathing apparatus should be used for breathing, and an encapsulated suit should be worn to prevent ammonia from reacting with our sweat or any other chemical burn. A mechanic ventilation will also be needed in the place of evacuation, so that the ammonia concentration in that area can be dispersed.

7 0

3 years ago

Read 2 more answers

Bob and Alice are solving practice problems for CSE 2320. They look at this code: for(i = 1; i <= N; i = (i*2)+17 ) for(k = i

MissTica

Answer:

Alice is correct.

The loop are dependent.

Explanation:

for(i = 1; i <= N; i = (i*2)+17 )

for(k = i+1; k <= i+N; k = k+1) // notice i in i+1 and i+N

printf("B")

This is a nested for-loop.

After the first for-loop opening, there is no block of statement to be executed rather a for-loop is called again. And the second for-loop uses the value of i from the first for-loop. The value of N is both called from outside the loop.

So, the second for-loop depend on the first for loop to get the value of i. For clarity purpose, code indentation or use of curly brace is advised.

8 0

3 years ago

Read 2 more answers