PPE is the first level of protecting an employee from hazards on the job site.

A particle moving on a straight line has acceleration a = 5-3t, and its velocity is 7 at time t = 2. If s(t) is the distance fro

Vikki [24]

Given acceleration a = 5-3t, and its velocity is 7 at time t = 2, the value of s2 - s1 = 7

<h3>How to solve for the value of s2 - s1</h3>

We have

= $\frac{dv}{dt} =v't = 5-3t\\\\\int\limits^a_b {v'(t)} \, dt$

$= \int\limits^a_b {(5-3t)} \, dt$

$5t - \frac{3t^2}{2} +c$

v2 = 5x2 - 3x2 + c

= 10-6+c

= 4+c

$s(t) = \frac{5t^2}{2} -\frac{t^3}{2} +3t + c$

S2 - S1

$=(5*\frac{4}{2} -\frac{8}{2} +3*2*c)-(\frac{5}{2} *1^2-\frac{1^2}{2} +3*1*c)$

= 6 + 6+c - 2+3+c

12+c-5+c = 0

7 = c

Read more on acceleration here: brainly.com/question/605631

5 0

2 years ago

Using the Distortion-Energy failure theory: 8. (5 pts) Calculate the hydrostatic and distortional components of the stress 9. (1

WITCHER [35]

Answer:

Detailed solution is given below:

7 0

4 years ago

Match the test to the property it measures.

Vinvika [58]

Answer:

a. Rockwell 3. hardness

b. Instron 2. stress vs strain

c. Charpy 1. impact strength

d. Fatigue 4. Endurance Limit

e. Brinell 3. hardness

f. Izod 1. impact strength

Explanation:

Izod and Charpy are the impact strength testing procedure of a material in which a heavy hammer is attached to an arm is released to impact on the test specimen. In Izod test the specimen with v-notch is held vertical with the notch facing outward while in Charpy test the specimen is supported horizontally with notch facing inward to the impacting hammer.

Instron testing system does universal testing of the material which gradually applies the load recording all the stresses and the corresponding strains until the material fails.

Fatigue is the property of a material due to which it fails under the repeated cyclic loading by the initiation and propagation of cracks. The property of a material resist failure subjected to infinite number of repeated cyclic loads below a certain stress limit.

Rockwell and Brinell are the hardness testing methods. In Rockwell test an intender ball is firstly pressed against the specimen using minor load for a certain time and then a major load is pressed against it for a certain time. After the intender is removed the depth of impression on the surface is measured while in case of Brinell hardness we apply only one load against the intender ball for a certain time and after its removal the radius of impression is measured.

7 0

3 years ago

You can help build a safe work environment by using your knowledge of violence prevention strategies to spot what?

Ostrovityanka [42]

Answer:

warning signs

Explanation:

give directions on your surroundings

4 0

3 years ago

A race car is travelling around a circular track. The velocity of the car is 20 m/s, the radius of the track is 300 m, and the m

Zielflug [23.3K]

Answer:

μ = 0.136

Explanation:

given,

velocity of the car = 20 m/s

radius of the track = 300 m

mass of the car = 2000 kg

centrifugal force

$F_c = \dfrac{mv^2}{r}$

$F_c = \dfrac{2000\times 20^2}{300}$

F c = 2666. 67 N

F f= μ N

F f = μ m g

2666.67 = μ × 2000 × 9.8

μ = 0.136

so, the minimum coefficient of friction between road surface and car tyre is equal to μ = 0.136

5 0

4 years ago