Answer:
A page that gets a Didn't Load flag
Pages with an obvious problem with functionality or errors in displaying content
Explanation:
The main reason why a page gets Page Quality rating Low/Lowest is if it can't be shown for one reason or another.
A page with mismatch between the location of the page and the rating location, does have a mismatch but some form of a page is shown.
A file type other than a webpage displays that specific file type in a page framework, so page is shown
Other two do not show a page, so they will get a PQ rating Low/Lowest
Answer:
a. 2^6, or 64 opcodes.
b. 2^5, or 32 registers.
c. 2^16, or 0 to 65536.
d. -32768 to 32768.
Explanation:
a. Following that the opcode is 6 bits, it is generally known that the maximum number of opcodes should be 2^6, or 64 opcodes.
b. Now, since the size of the register field is 5 bits, we know that 2^5 registers can be accessed, or 32 registers.
c. Unsigned immediate operand applies to the plus/minus sign of the number. Since unsigned numbers are always positive, the range is from 0 to 2^16, or 0 to 65536.
d. Considering that the signed operands can be negative, they need a 16'th bit for the sign and 15 bits for the number. This means there are 2 * (2^15) numbers, or 2^16. However, the numbers range from -32768 to 32768.
Answer:
yes it is odd beacuse 3 is a odd number
Answer:
A and C
Explanation:
Option A:
In IPv6 there is a rule to reduce an IPv6 address when there are two or more consecutive segments of zeros just one time. This rule says that you can change the consecutive zeros for “::”
Here is an example
How to reduce the following IPv6 address?
ff02:0000:0000:0000:0000:0000:0000:d500
Ans: ff02::d500
Example 2:
2001:ed02:0000:0000:cf14:0000:0000:de95
Incorrect Answer -> 2001:ed02::cf14::de95
Since the rule says that you can apply “::” just one time, you need to do it for a per of zero segments, so the correct answer is:
Correct Answer -> 2001:ed02::cf14:0:0:de95
Or
2001:ed02:0:0:cf14::de95
Option C:
Since in IPv6 there are
available addresses which means 340.282.366.920.938.463.463.374.607.431.768.211.456 (too many addresses), there is no need of NAT solution, so each device can have its own IP address by the same interface to have access through the internet if needed. If not, you can block the access through internet by the firewall.
Alternative 1:A small D-cache with a hit rate of 94% and a hit access time of 1 cycle (assume that no additional cycles on top of the baseline CPI are added to the execution on a cache hit in this case).Alternative 2: A larger D-cache with a hit rate of 98% and the hit access time of 2 cycles (assume that every memory instruction that hits into the cache adds one additional cycle on top of the baseline CPI). a)[10%] Estimate the CPI metric for both of these designs and determine which of these two designsprovides better performance. Explain your answers!CPI = # Cycles / # InsnLet X = # InsnCPI = # Cycles / XAlternative 1:# Cycles = 0.50*X*2 + 0.50*X(0.94*2 + 0.06*150)CPI= 0.50*X*2 + 0.50*X(0.94*2 + 0.06*150) / X1= X(0.50*2 + 0.50(0.94*2 + 0.06*150) ) / X= 0.50*2 + 0.50(0.94*2 + 0.06*150)= 6.44Alternative 2:# Cycles = 0.50*X*2 + 0.50*X(0.98*(2+1) + 0.02*150)CPI= 0.50*X*2 + 0.50*X(0.98*(2+1) + 0.02*150) / X2= X(0.50*2 + 0.50(0.98*(2+1) + 0.02*150)) / X= 0.50*2 + 0.50(0.98*(2+1) + 0.02*150)= 3.97Alternative 2 has a lower CPI, therefore Alternative 2 provides better performance.