All categories

2 years ago

Because CMB radiation was _____ throughout the universe, scientists can only relate the source to the big bang.

1 answer:

6 0

Answer: 1 The correct answer is that CMB radiation was spread uniformly throughout the whole universe.This was related to big band theory because this theory predicts that the universe was a very hot place and as it cooled down it should have been filled with laterally the remnant heat over from the Big Bang called as cosmic microwave background.

Answer: 2 CMB radiation was discovered accidentally when Penzias and Wilson were performing some experiment and they noticed a ' hum' noise that was constantly detected by the antenna even after removing all the disturbing sources.

Then it was realized that it is cosmic microwave background radiation.

You might be interested in

What effect would this have on the momentum?

Mariana [72]

Momentum describes an object in motion and is determined by the product of two variables: mass and velocity. Mass -- the weight of an object -- is usually measured in kilograms or grams for momentum problems. Velocity is the measure of distance traveled over time and is normally reported in meters per second. Examining the possible changes in these two variables identifies the different effects momentum can have on an object in motion.

6 0

2 years ago

The starter motor of a car engine draws a current of 140 A from the battery. The copper wire to the motor is 4.20 mm in diameter

GenaCL600 [577]

Answer:

(a)106.4C

b)0.5676mm

Explanation:

(a)To get the charge that have passed through the starter then The current will be multiplied by the duration

I= current

t= time taken

Q= required charge

Q= I*t = 140*0.760 = 106.C

(b) b. How far does an electron travel along the wire while the starter motor is on?(mm)

diameter of the conductor is 4.20 mm

But Radius= diameter/2= 4.20/2=

The radius of the conductor is 2.1mm, then if we convert to metre for consistency same then

radius of the conductor is 0.0021m.

We can now calculate the area of the conductor which is

A = π*r^2

= π*(0.0021)^2 = 13.85*10^-6 m^2

We can proceed to calculate the current density below

J = 140/13.85*10^-6 = 10108303A/m

According to the listed reference:

Where e= 1.6*10^-19

n= 8.46*10^28

Vd = J/(n*e) = 10108303/ ( 8.46*10^28 * 1.6*10^-19 ) =0.0007468m/s=0 .7468 mm/s

Therefore , the distance traveled is:

x = v*t = 0.7468 * 0.760 = 0.5676mm

7 0

2 years ago

At 9:00 on Saturday morning, two bicyclists heading in opposite directions pass each other on a bicycle path.The bicyclist headi

notka56 [123]

Between 9:00 am and 10:45 am, there have been 1 hour and 45 minutes or 1.75 hours have passed. Let x be the speed of the slower cyclist and x+ 5 be the rate of the second cyclist. The given situation is best represented through the equation below,
x(1.75) + (x + 5)(1.75) = 47.25 km
The value of x from the equation is 11. Thus, the two bicyclists' rates are 11 km/h and 16 km/h.

3 0

2 years ago

Read 2 more answers

In situations involving equal masses, chemical reactions produce less energy than what reactions?

Liula [17]

in situations involving equal masses, chemical reactions produce less energy than nuclear reactions.

7 0

3 years ago

Read 2 more answers

Is velocity ratio of a machine affected by applying oil on it?Explain with reason.

disa [49]

Factors affecting friction

The intensity of friction depends on following factors: i) The area involved in friction. ii) The pressure applied on the surfaces. Force = Pressure ´ Area Frictional force will increase, if the area of contact will increase or if pressure applied on the surface increased.

Methods to reduce friction

i) Polish the contact surface. ii) Put oil or grease so that it fills in the small gaps of the flat parts. iii) Use ball bearings to reduce area of contact between rotating parts.

Lubrication

Following methods can be used to reduce friction: Oil is either thin or viscous. It depends upon SAE No. of oil. (SAE means Society of Automotive Engineers). If we use very viscous oil, it does not reach all the parts. Very thin oil will flows away easily and gets wasted. Grease is used in such cases. It is generally used around ball-bearing. Normal grease or oil is never used where there is high pressure, high temperature and high speed. Special lubricants are used in such cases. In cold season the oil becomes thick and in hot season it becomes thin. Therefore selection of lubrication also depends on the season. It is always advisable to refer operating manual of the equipment before selecting the lubricant.

6 0

3 years ago