Great Question! So the plug will go into the wall and electricity will hit the cord and power through the cord into the charger (Cordless) Now if you talking mobile phones such as iPhones. The battery powers wire and hardware to power your little mobile phone! Hope this helps.
A sixteen bit microprocessor chip used in early IBM PCs. The Intel 8088 was a version with an eight-bit externaldata bus.
The Intel 8086 was based on the design of the Intel 8080 <span>and </span>Intel 8085 (it was source compatible with the 8080)with a similar register set, but was expanded to 16 bits. The Bus Interface Unit fed the instruction stream to theExecution Unit through a 6 byte prefetch queue, so fetch and execution were concurrent - a primitive form ofpipelining (8086 instructions varied from 1 to 4 bytes).
It featured four 16-bit general registers, which could also be accessed as eight 8-bit registers, and four 16-bit indexregisters (including the stack pointer). The data registers were often used implicitly by instructions, complicatingregister allocation for temporary values. It featured 64K 8-bit I/O (or 32K 16 bit) ports and fixed vectored interrupts.There were also four segment registers that could be set from index registers.
The segment registers allowed the CPU to access 1 meg of memory in an odd way. Rather than just supplyingmissing bytes, as most segmented processors, the 8086 actually shifted the segment registers left 4 bits and addedit to the address. As a result, segments overlapped, and it was possible to have two pointers with the same valuepoint to two different memory locations, or two pointers with different values pointing to the same location. Mostpeople consider this a brain damaged design.
Although this was largely acceptable for assembly language, where control of the segments was complete (it couldeven be useful then), in higher level languages it caused constant confusion (e.g. near/far pointers). Even worse, thismade expanding the address space to more than 1 meg difficult. A later version, the Intel 80386, expanded thedesign to 32 bits, and "fixed" the segmentation, but required extra modes (suppressing the new features) forcompatibility, and retains the awkward architecture. In fact, with the right assembler, code written for the 8008 canstill be run on the most <span>recent </span>Intel 486.
The Intel 80386 added new op codes in a kludgy fashion similar to the Zilog Z80 and Zilog Z280. The Intel 486added full pipelines, and clock doubling (like <span>the </span>Zilog Z280).
So why did IBM chose the 8086 series when most of the alternatives were so much better? Apparently IBM's own engineers wanted to use the Motorola 68000, and it was used later in the forgotten IBM Instruments 9000 Laboratory Computer, but IBM already had rights to manufacture the 8086, in exchange for giving Intel the rights to its bubble memory<span> designs.</span> Apparently IBM was using 8086s in the IBM Displaywriter word processor.
Other factors were the 8-bit Intel 8088 version, which could use existing Intel 8085-type components, and allowed the computer to be based on a modified 8085 design. 68000 components were not widely available, though it could useMotorola 6800 components to an <span>extent.
</span>
Hope this helps
In an <u>Internet-based system</u>, the web becomes an integral part of the application, rather than just a communication channel, and systems analysts need new application development tools and solutions to handle the new systems.
d) Internet-based system
<u>Explanation:</u>
Web information system, or web-based information system, is a data framework that utilizes Internet web advancements to convey data and administrations, to clients or other data frameworks/applications.
It is a product framework whose primary intention is to distribute and keep up information by utilizing hypertext-based standards. In an Internet-based system, the Web turns into a fundamental piece of the application, instead of only a correspondence channel, and frameworks investigators need new application advancement instruments and solutions to handle the new systems.
The program is an illustration of loops.
Loops are used to perform repetitive and iterative operations.
The program in C++ where comments are used to explain each line is as follows:
#include <iostream>
using namespace std;
int main(){
//This declares and initializes all variables
string star = "*", blank = " ", temp;
//The following iteration is repeated 8 times
for (int i = 1; i <= 8; i++) {
//The following iteration is repeated 8 times
for (int j = 1; j <= 8; j++) {
//This prints stars
if (j % 2 != 0) {
cout << star;
}
//This prints blanks
else if (j % 2 == 0) {
cout << blank;
}
}
//This swaps the stars and the blanks
temp = star;
star = blank;
blank = temp;
//This prints a new line
cout << endl;
}
}
Read more about similar programs at:
brainly.com/question/16240864
<span><span>The correct answer is: </span>compare
the fonts of the two texts.</span>
You can access Reveal Formatting by selecting the desired
tet and pressing Shift+F1. By opening this pane you will be able to see the
paragraph formatting, font size, font type and line spacing.
