1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
Kitty [74]
3 years ago
11

Which of the following materials is created by a natural, eco-friendly process, is a renewable resource, and is a primary buildi

ng material in construction?
wood

rubber

glass

metal
Engineering
2 answers:
Vladimir79 [104]3 years ago
7 0
I would say rubber would be the correct answer. I’m not sure but hope this helps!
Romashka-Z-Leto [24]3 years ago
5 0
Wood because is naturally made and is a primary building material
You might be interested in
Which option identifies the type of power system Tommy will design in the following scenario?
Sedaia [141]

Answer:

diagram of an electrical curcuit

an sketch of an HVAC system

Also 3D image of a hydrualic piston

se

7 0
3 years ago
a turbine operating at steady state at 500 kPa, 860 K and exists at 100 kPa. A temperature sensor indicates that the exit air te
noname [10]

Answer:

Given:

P₁ = 500 kPa

T₁ = 860 K

P₂= 100 kPa

T₂ = 460 K

Let's take entropy properties of T1 and T2 from ideal properties of air,

at T = 860K, s(T₁) = 2.79783 kJ/kg.K

at T = 460K, s(T₂) = 2.13407 kJ/kg.K

using entropy balance equation:

\frac{\sigma _cv}{m} = s(T_2)- s(T_1) - R In [\frac{P_2}{P_1}]

\frac{\sigma _cv}{m} = 2.79783 - 2.13407 - 0.287 In [\frac{100}{500}]

= - 0.2018 kJ/kg. K

In this case the entropy is negative, which means the value of exit temperature is not correct, beacause entropy should always be positive(>0).

8 0
3 years ago
Calculate the areas under the stress-strain curve (toughness) for the materials shown in Fig. below, (a) plot them as a
defon

Answer:

Explanation:

Wow

5 0
3 years ago
R1 stands for what?
balandron [24]

Answer:

I think the answer is A. resistor 1

*am sorry if I get it wrong I just want to help people pass*

8 0
3 years ago
Key length is designed to provide desired factor of safety<br> a. True<br> b. False
zhuklara [117]

Answer: true

Explanation:

A key is a machine element that us used to connect the element of a rotating machine to a shaft. It should be noted that the key hinders the relative rotation that may take place between the two parts.

Key length is designed to provide desired factor of safety. It should also be noted that the factor of safety shouldn't be much and the key length is typically limited to the hub length.

8 0
3 years ago
Other questions:
  • For flow over a plate, the variation of velocity with vertical distance y from the plate is given as u(y) = ay − by2 where a and
    10·1 answer
  • Water flows at 0.1 m3 /s through the 100– mm–diameter nozzle and strikes the vane on the 150–kg cart, which is originally at res
    13·1 answer
  • A stream of air enters a 7.00-cm ID pipe at a velocity of 30.0 m/s at 27.0°C and 1.80 bar (gauge). At a point downstrream, the a
    15·1 answer
  • Parity Detect of Three Inputs 20 pts. (EVEN) a) Draw a function table showing the three data lines and the output function F. 4
    9·1 answer
  • Design a solid steel shaft to transmit 14 hp at a speed of 2400rpm f the allowable shearing stress is given as 3.5 ksi.
    10·1 answer
  • What is the built-in pollution control system in an incinerator called
    6·1 answer
  • The four important principles of flight are lift, drag, thrust, and _____.
    7·1 answer
  • State two reasons why industrial files must be always be used fitted upon the individual
    8·1 answer
  • Write down about the water source selection criteria​
    9·1 answer
  • A coil having resistance of 7 ohms and inductance of 31.8 mh is connected to 230v,50hz supply.calculate 1. The circuit current 2
    6·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!