Ingestion of foreign substances by macrophages and yeast cells by an amoeba is known as

Biology

1 answer:

Iteru [2.4K]3 years ago

3 0

Ingestion of foreign substances by macrophages and yeast cells by an amoeba is known as <u>Phagocytosis</u>

<u>Explanation:</u>

Phagocytosis that is the name given to the process of ingestion of foreign particles by macrophages. In human body the white blood cells does this function. Macrophages is found in all the tissues. Any foreign particle entering the body is engulfed by this process hence protecting the organisms.

Once a bacteria enters the body it is at once detected and recognised as the foreign particle. Then it is attached to the phagocyte. Then it is engulfed into a vesicle called phagosome. Then this is killed by the process of phagocytosis.

You might be interested in

I'll give you a brainliest if is right or at least shows some effort

insens350 [35]

Answer:

Celestial microwave radiation found a strange microwave signal causing background noise in the radio telescope. The signal came from every direction. The young universe would have been very hot. The microwave background radiation is the remaining heat from the Big bang.

I tried my hardest and this is what I put on MY test so good luck

4 0

3 years ago

Phage lambda lytic versus lysogenic phases are controlled by two proteins, Cro which leads to lysis and CII which leads to lysog

Juli2301 [7.4K]

Answer:

The maintainance of the lytic and the lysogenic cycle is done by the Cro and the lambda repressor proteins when the number of bacteria is higher than the number of viruses that is the mode of infectivity or MOI the virus under goes the lytic cycle. This is done by the cleaving of the proteins.

So high nutrient concentration in the gut promotes the growth of the E coli that forms a protease that cleaves the Cro protein and causes the activation of the lysis in the bacteria. So in the high nutrient concentration the bacteria is itself responsible for its lysis.

7 0

3 years ago

Which statements describe a situation with a displacement of zero

MA_775_DIABLO [31]

An object that starts and ends at the same point would have zero displacements.

<h3>What is displacement?</h3>

Displacement is the property of a body or an object to be moved from one place to another.

Thus a body that moves or is moved from point A to point B has been displaced.

A body with zero displacements either did not move at all or finished at the same point it started.

For example, a body that moves from point A to B, and then back to A will have zero displacements.

More on displacement can be found here: brainly.com/question/11934397

#SPJ1

5 0

1 year ago

1. What are the independent and dependent variables in each of the experiments?

Dafna1 [17]

The independent variables are temperature, airflow, and light and the dependent variable in each of the experiments is evaporation.
The schematic representation in the diagram helps in the understanding of the setup for the experiments.
The level of temperature, the rate of airflow, and the intensity of light must be controlled in the experiments.
A person will not be confident in experiment 3 results as the temperature is the independent variable that alters the results of evaporation.

<h3>What are the four foremost factors of a managed test?</h3>

When possible, scientists take a look at their hypotheses through the use of managed experiments. A managed test is a systematic take look at executed below-managed conditions, which means that simply one (or a few) elements are modified at a time, even as all others are saved consistently. We'll appear carefully at managed experiments within side the subsequent section.

In the three experiments, the dependent variable is evaporation, as it changes with the change in another variable.

The independent variable in experiment 1 is temperature, experiment 2 is airflow, and experiment 3 is light.

The experiment can be understood better with the representation of the schematic that shows the setup to analyze how the experiment was performed. Therefore the diagram must add the schematic of the experiment.

The controlled items in the experiment are the variables that are set at the particular unit to form the result. the controlled item in experiment 1 is temperature, experiment 2 is airflow from the fan, and experiment 3 is the intensity of light.

The result of experiment 3 is based on the dependence on the intensity of light keeping temperature constant and controlled. If the temperature is not controlled in the experiment then it may lead to an alteration in the results as it depends on both light and temperature.

The flow chart for the increase in pressure affecting the evaporation is given in the image attached.