In the legend of sleeping Hallow what does Ichabod Crane fear the most

Which is NOT a component of a relationaldatabase?

MaRussiya [10]

Answer: 4) Hierarchy

Explanation:

The main components of the relational database are table, entity and attributes. As, relational data base is the method of arranging and maintaining the data and each table in the database contain data in the entity and the attributes. Hierarchy is not the component of the database as it is included in the type oh hierarchical database not in relational database.

5 0

3 years ago

If you could make another device "smart" and have

konstantin123 [22]

Answer:

I would 100% make myself a SmartToaster (Trademark Pending)

Explanation:

A simple explanation would be I like toast

7 0

3 years ago

[Assembly Language]Extended Subtraction Procedure.Create a procedure named Extended_Sub --(Receives: ESI and EDI point to the tw

alex41 [277]

Answer:

Modern (i.e 386 and beyond) x86 processors have eight 32-bit general purpose registers, as depicted in Figure 1. The register names are mostly historical. For example, EAX used to be called the accumulator since it was used by a number of arithmetic operations, and ECX was known as the counter since it was used to hold a loop index. Whereas most of the registers have lost their special purposes in the modern instruction set, by convention, two are reserved for special purposes — the stack pointer (ESP) and the base pointer (EBP).

For the EAX, EBX, ECX, and EDX registers, subsections may be used. For example, the least significant 2 bytes of EAX can be treated as a 16-bit register called AX. The least significant byte of AX can be used as a single 8-bit register called AL, while the most significant byte of AX can be used as a single 8-bit register called AH. These names refer to the same physical register. When a two-byte quantity is placed into DX, the update affects the value of DH, DL, and EDX. These sub-registers are mainly hold-overs from older, 16-bit versions of the instruction set. However, they are sometimes convenient when dealing with data that are smaller than 32-bits (e.g. 1-byte ASCII characters).

When referring to registers in assembly language, the names are not case-sensitive. For example, the names EAX and eax refer to the same register.

Explanation:

5 0

3 years ago

Assume that name is a variable of type String that has been assigned a value. Write an expression whose value is a String contai

Stella [2.4K]

Corrected (Modified) Question:

i. Assume that name is a variable of type String that has been assigned a value. Write an expression whose value is a String containing the last character of the value of name. So if the value of name were "Smith" the expression's value would be "h".

ii. Given a String variable named sentence that has been initialized, write an expression whose value is the number of characters in the String referred to by sentence.

Explanation of the corrected question

The whole question has been numbered (i) and (ii) just to separate or divide it into clearer sub questions.

Some parts of the question has also been removed since they are repetition of a part of the question.

Answer:

(i) name.charAt(name.length() - 1)

(ii) sentence.length()

Explanation:

No language has been specified in the question for the code to be written in. However, I have chosen to write it in Java.

(i) In Java, to get a particular character in a string str, the function, charAt(x) is used, where x in the function represents the index of the character to be fetched. This is written as str.charAt(x).

In our case, x is the index of the last character in our string. To get the index of the last character in a string say str, the length of the string itself is used. However, indexing starts at zero. Therefore, to get the index, it will be the 1 subtracted from the length of the string as follows:

str.length() - 1

But note that, to get the length of a string, the method length() is used. For example if,

String str = "omobowale";

str.length() will return 9

Now to the question at hand, our string variable name is name.

Therefore to get its last character, we write:

name.charAt(name.length() - 1)

So if;

name = "Smith";

name.charAt(name.length() - 1) will return "h"

(ii) As explained in (i) above, to get the length (number of characters) of the variable string sentence, we simply write;

sentence.length()

PS: The length of a string is the number of characters present in the string.

Hope this helps!

3 0

3 years ago

Malware that is spread through security warnings or advertisements for antivirus software is known as

svetlana [45]

It is known as A bug

5 0

4 years ago