1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
finlep [7]
4 years ago
9

Use CAD software to simulate the common–emitter amplifier and characterize itsperformance. The simulations should include: 1) a

dc bias analysis to verify thebias point of the transistor, 2) a transient analysis to verify the ac gain of the CE amplifier, 3) an ac analysis to characterize the frequency response of the circuit (i.e.,magnitude gain and phase shift over frequency) , 4) a parameter sweep analysisto characterize the output voltage versus load resistance (i.e., determine range of acceptable loads), 5) a temperature stability analysis (to determine variations innominal gain for temperature variations over the standard operating temperaturerange), and 6) input and output resistance (determined experimentally using thetest source method).
Engineering
1 answer:
Stells [14]4 years ago
4 0

Use CAD software to simulate the common–emitter amplifier and characterize itsperformance is described below

Explanation:

Characteristics of Common Emitter Amplifier

  • The voltage gain of common emitter amplifier is medium.
  • The power gain is high in the common emitter amplifier.
  • There is a phase relationship of 180 degrees in input and output.
  • In the common emitter amplifier, the input and output resistors are medium.

The common emitter circuit is popular because it's well-suited for voltage amplification, especially at low frequencies. Common-emitter amplifiers are also used in radio frequency transceiver circuits. Common emitter configuration commonly used in low-noise amplifiers.

Why CE configuration having 180 degree phase shift in a CE amplifier, when base voltage increase, base current increases. It causes an increase in collector current also. The collector current causes a voltage drop in the collector resistor. ... Thus it produces a 180 phase shift.

⦁ CE is most widely used because it provides the voltage gain required for most of the day to day applications of preamp and power amps. ... ⦁ Common emitter is the most basic configuration for amplifier circuits. It also provide the maximum transconductance or voltage gain for a given load.

This type of biasing arrangement uses two resistors as a potential divider network across the supply with their center point supplying the required Base bias voltage to the transistor. Voltage divider biasing is commonly used in the design of bipolar transistor amplifier circuits.

You might be interested in
The two boxcars A and B have a weight of 20000lb and 30000lb respectively. If they coast freely down the incline when the brakes
kolbaska11 [484]

Answer:

T=5.98 kips

Explanation:

First, introduce forces, acting on both cars:

on car A there are 4 forces acting: gravity force mA*g, normal reaction force, friction force and force T- it represents the interaction between cars A and B. On car B, there are three forces acting: gravity force, normal reaction force and force T. Note, that force T is acting on both cars, but it has opposite direction. Force T, acting on car A has direction, opposite to the friction force, whether the T, acting on B, is directed backwards- in the same direction with the friction force. Note, that both cars have the same acceleration, which is directed backwards.

Once the forces were established, we can write components of the Second Newtons Law on vertical and horizontal axes, considering that horizontal axis is directed backwards- in the same direction with the acceleration:

For car A on the vertical axis the equation is: -mAg+NA=0

For car A on the horizontal axis, the equation is: Ffr-T=mAa

For car B, on the vertical axis the equation is: -mBg+NB=0

For car B, on the horizontal axis, the equation is: T=mBa

We need to solve these equations to find force T, knowing that Ffr=μmAg, where

After the transformations, the equations for acceleration and force in the coupling will be:

a=(μmAg)/(mA+mB)=6.43 ft/s2- note, that the given answer is not correct for the given numerical values;

and force T: T=μmAmBg/(mA+mB)=6.0 kips- note, that the force answer is in line with the given numerical value

5 0
4 years ago
What are the horizontal structures beneath a slab that help transfer the load from the slab to the columns?
Delicious77 [7]

Answer: D) Beams

Explanation:

3 0
2 years ago
Read 2 more answers
Technician A says when the brakes are applied in a vacuum booster, the vacuum control valve is closed. Technician B says the vac
Wewaii [24]

Answer:

Technician A only

Explanation:

The application of the breaks by stepping on the break pedal moves the pedal pushrod and plunger forward within the diaphragm plate, bringing about the contact between the vacuum port seal and the vacuum valve that closes the vacuum port and the passage that connects the left and right chambers such that the pressure in one chamber and te vacuum in the other chamber are held steady.

4 0
3 years ago
A motor vehicle has a mass of 1200kg and the road wheels have a radius of 360mm. The engine rotating parts have a moment of iner
mihalych1998 [28]

Answer:

manda a senha do brainly bloquearam os amigos e você vai ver o meu perfil completo a minha amiga Jeciane estamos fazendo uma academia de lima e você vai ver o meu perfil completo a minha amiga Jeciane estamos completo a minha amiga Jeciane estamos fazendo uma academia de lima e você vai ver o meu perfil você vai ver o meu perfil você vai ver o meu perfil completo a minha amiga Jeciane estamos fazendo uma academia de lima e fazendo uma academia de lima e fazendo uma academia de lima e fazendo uma academia de lima e fazendo uma academia de lima e fazendo uma academia de lima e você vai ver o meu perfil completo a minha amiga Jeciane estamos fazendo

Explanation:

Marcar como melhor porfavo

6 0
4 years ago
A large plate is fabricated from a steel alloy that has a plane strain fracture toughness of 78 MPa (70.98 ksi). If the plate is
Reika [66]

Answer:

minimum length of a surface crack is 15.043 mm

Explanation:

given data

strain fracture toughness K = 78 MPa

tensile stress = 345 MPa

Y = 1.04

to find out

minimum length of a surface crack

solution

we find here length of critical interior flaw from formula that is

α  =  \frac{1}{\pi} (\frac{K}{\sigma Y})^2     ....................1

put here value we get

α  =  \frac{1}{\pi} (\frac{78*\sqrt{10^3} }{345*1.04})^2

α  = 15.043 mm

so minimum length of a surface crack is 15.043 mm

7 0
3 years ago
Other questions:
  • List the thermal conductivities of five
    15·1 answer
  • Water is the working fluid in an ideal Rankine cycle. Superheatedvapor enters the turbine at 10MPa, 480°C, and the condenser pre
    10·1 answer
  • The density of a fluid is given by the empirical equation rho 70:5 exp 8:27 107 P where rho is density (lbm/ft3 ) and P is press
    6·1 answer
  • The outer surface of a spacecraft in space has an emissivity of 0.6 and an absorptivity of 0.2 for solar radiation. If solar rad
    12·1 answer
  • An inverting amplifier with +11 V supply voltages normally has a sinusoidal output of 10 Vpp. When checking the circuit with an
    11·1 answer
  • • Differentiate between laboratory and industrial reactors​
    11·1 answer
  • Which is an alloy made up of iron and carbon and has high compressive and tensile strength?
    6·1 answer
  • A heating system must maintain the interior of a building at TH = 20 °C when the outside temperature is TC = 2 °C. If the rate o
    10·1 answer
  • g Asbestos is a fibrous silicate mineral with remarkably high tensile strength. But is no longer used because airborne asbestos
    5·1 answer
  • Policeman says, "Son, you can't stay here"
    9·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!