Answer:
sorry I dont now the answer bro i am so sorry xd ;'(
I believe it goes as the following::
1) Waves transfer energy without moving particles
2) The two types of waves are longitudinal and transverse waves OR The two types of waves are mechanical and electromagnetic waves. Both are applicable and should be correct!
Parallel circuit
Advandages: 1. Every unit that is connected in a parallel circuit gets equal amount of voltage.
2. It becomes easy to connect or disconnect a new element without affecting the working of other elements.
3. If any fault happened to the circuit, then also the current is able to pass through the circuit through different paths.
Disadvantages: 1. It requires the use of lot of wires.
2. We cannot increase or multiply the voltage in a parallel circuit.
3. Parallel connection fails at the time when it is required to pass exactly same amount of current through the units.
series circuit
Advantages: 1. Series circuits do not overheat easily. This makes them very useful in the case of something that might be around a potentially flammable source, like dry plants or cloth.
2. Series circuits are easy to learn and to make. Their simple design is easy to understand, and this means that it’s simple to conduct repairs .
3. we can add more power devices, they have a higher output in terms of voltage .
4. The current that flows in a series circuit has to flow through every component in the circuit. Therefore, all of the components in a series connection carry the same current.
Disadvantages: 1.If one point breaks in the series circuit,the total circuit will break.
2. As the number of components in a circuit increases ,greater will be the circuit resistance.
Answer:
The x-component of 
is 56.148 newtons.
Explanation:
From 1st and 2nd Newton's Law we know that a system is at rest when net acceleration is zero. Then, the vectorial sum of the three forces must be equal to zero. That is:
(1)
Where:
, 
, 
- External forces exerted on the ring, measured in newtons.
- Vector zero, measured in newtons.
If we know that ![\vec F_{1} = (70.711,70.711)\,[N]](https://tex.z-dn.net/?f=%5Cvec%20F_%7B1%7D%20%3D%20%2870.711%2C70.711%29%5C%2C%5BN%5D)
, ![\vec F_{2} = (-126.859, 46.173)\,[N]](https://tex.z-dn.net/?f=%5Cvec%20F_%7B2%7D%20%3D%20%28-126.859%2C%2046.173%29%5C%2C%5BN%5D)
, 
and ![\vec O = (0,0)\,[N]](https://tex.z-dn.net/?f=%5Cvec%20O%20%3D%20%280%2C0%29%5C%2C%5BN%5D)
, then we construct the following system of linear equations:
(2)
(3)
The solution of this system is:
, 
The x-component of is 56.148 newtons.
In the writing of ionic chemical formulas the value of each ion's charge is crossed over in the crossover rule.
Rules for naming Ionic compounds
- Frist Rule
The cation (element with a negative charge) is written first in the name then the anion(element with a positive charge) is written second in the name.
- Second rule
When the formula unit contains two or more of the same polyatomic ion, that ion is written in parentheses with the subscript written outside the parentheses.
Example: Sodium carbonate is written as Na₂CO₃ not Na₂(CO)₃
- Third rule
If the cation is a metal ion with a fixed charge then the name of the cation will remain the same as the (neutral) element from which it is derived (Example: Na+ will be sodium).
If the cation is a metal ion with a variable charge, the charge on the cation is indicated using a Roman numeral, in parentheses, immediately following the name of the cation (example: Fe³⁺ = iron(III)).
- Fourth rule
If the anion is a monatomic ion, the anion is named by adding the suffix <em>-ide</em> to the root of the element name (example: F = Fluoride).
The oxidation state of each ion is also important, thus in the crossover rule, the value of each ion's charge is crossed over.
Learn more about chemical formulas here:
<u>brainly.com/question/11995171</u>
#SPJ4
