All categories

2 years ago

C) Three AC voltages are as follows:

Engineering

1 answer:

stich3 [128]2 years ago

4 0

Answer:

What is the probability of selecting the 4 of spade or black diamond from a deck of 52 playing cards?

a) 2/52

b) 4/52

c) 3/52

d) 1/5

Explanation:

You might be interested in

If you are a government authority what extend will you modify the existing policy

mr_godi [17]

Answer:

Explanation:

dkdndidodd ndidkjeeiwonejeeidmdnddkdidfmndd

4 0

3 years ago

Determine the reactor volume (assume a CSTR activated sludge aerobic reactor at steady state) required to treat 5 MGD of domesti

12345 [234]

Answer:

1.0MG

Explanation:

to solve this problem we use this formula

S₀-S/t = ksx --- (1)

the values have been given as

concentration = S₀ = 250mg

effluent concentration = S= 10mg

value of K = 0.04L/day

x = 3000 mg

when we put these values into this equation,

250-10/t = 0.04x10x3000

240/t = 1200

we cross multiply from this stage

240 = 1200t

t = 240/1200

t = 0.2

remember the question says that 5MGD is required to be treated

so the volume would be

v = 0.2x5

= 1.0 MG

4 0

1 year ago

A circular section of material is tested. The original specimen is 200 mm long and has a diameter of 13 mm. When loaded to its p

n200080 [17]

Answer:

modulus of elasticity = 100.45 Gpa,

proportional limit = 150.68 N/mm^2.

Explanation:

We are given the following parameters or data in the question as;

=> "The original specimen = 200 mm long and has a diameter of 13 mm."

=> "When loaded to its proportional limit, the specimen elongates by 0.3 mm."

=> " The total axial load is 20 kN"

Step one: Calculate the area

Area = π/ 4 × c^2.

Area = π/ 4 × 13^2 = 132.73 mm^2.

Step two: determine the stress induced.

stress induced = load/ area= 20 × 1000/132.73 = 150.68 N/mm^2.

Step three: determine the strain rate:

The strain rate = change in length/original length = 0.3/ 200 = 0.0015.

Step four: determine the modulus of elasticity.

modulus of elasticity = stress/strain = 150.68/0.0015 = 100453.33 N/mm^2 = 100.45 Gpa.

Step five: determine the proportional limit.

proportional limit = 20 × 1000/132.73 = 150.68 N/mm^2.

7 0

2 years ago

Read 2 more answers

A steel rod, which is free to move, has a length of 200 mm and a diameter of 20 mm at a temperature of 15oC. If the rod is heate

kherson [118]

Explanation:

thermal expansion ∝L = (δL/δT)÷L ----(1)

δL = L∝L + δT ----(2)

we have δL = 12.5x10⁻⁶

length l = 200mm

δT = 115°c - 15°c = 100°c

putting these values into equation 1, we have

δL = 200*12.5X10⁻⁶x100

= 0.25 MM

L₂ = L + δ L

= 200 + 0.25

L₂ = 200.25mm

12.5X10⁻⁶ *115-15 * 20

= 0.025

20 +0.025

D₂ = 20.025

as this rod undergoes free expansion at 115°c, the stress on this rod would be = 0

3 0

2 years ago

Steam enters an adiabatic turbine at 8 MPa and 500C with a mass flow rate of 3

Vinil7 [7]

Answer:

a)temperature=69.1C

b)3054Kw

Explanation:

Hello!

To solve this problem follow the steps below, the complete procedure is in the attached image

1. draw a complete outline of the problem

2. to find the temperature at the turbine exit use termodinamic tables to find the saturation temperature at 30kPa

note=Through laboratory tests, thermodynamic tables were developed, these allow to know all the thermodynamic properties of a substance (entropy, enthalpy, pressure, specific volume, internal energy etc ..)

through prior knowledge of two other properties such as pressure and temperature.

3. Using thermodynamic tables find the enthalpy and entropy at the turbine inlet, then find the ideal enthalpy using the entropy of state 1 and the outlet pressure = 30kPa

4. The efficiency of the turbine is defined as the ratio between the real power and the ideal power, with this we find the real enthalpy.

Note: Remember that for a turbine with a single input and output, the power is calculated as the product of the mass flow and the difference in enthalpies.

5. Find the real power of the turbine

3 0

2 years ago