1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
Ainat [17]
3 years ago
7

10. Aluminum-lithium (Al-Li) alloys have been developed by the aircraft industry to reduce the weight and improve the performanc

e of this aircraft. A commercial aircraft skin material having a density of 2.47g/cm3 is desired. Compute the concentration of Li (wt%) that is required.
Engineering
1 answer:
klio [65]3 years ago
8 0

Answer:

C_Li=2.3 %

Explanation:

<u>solution:</u>

<em>we know that the average density of a two component alloy is given by:</em>

ρ_avg=100/(C_1/ρ_1+C_2/ρ_2)

2.47 g/cm^3=100/(C_Li/ρ_Li+(100-C_Li)/ρ_aL)

<em>solving for C_Li we get,</em>

C_Li=2.3 %

You might be interested in
A team member who has been a good worker for many years has recently been doing poor work. You suspect that he may be tired of h
ohaa [14]

Answer:

You must follow the steps below to deal with employees who have poor performance. I hope that you will be able to handle all the issues after reading this answer.

Explanation:

Be specific with facts in hand

It is important to confront your employees about their respective actions. But to convince them about their withdrawal from lack of interest, it is imperative to have a consistent record at hand as well. For example, if the employee has been constantly delayed for a period of time, specify the precise details about the frequency and intensity of absenteeism. Be sure not to overdo your statements or use hard phrases to reduce employee self-esteem. Just be direct and precise. Reiterate the guidelines accordingly.

Consider the needs of your employees

Poor performance is not always the result of an employee's carelessness. There can be multiple genuine reasons for lack of performance and it can vary from person to person. The first is to understand the reason and judge whether they are genuine or not. Even if they aren't, don't let the other person know. Focus on your concerns and provide solutions accordingly. For example, if your employees cannot focus on their work due to some personal stress, make appointments for the counseling sessions and make sure they can get back on track.

Focus on feedback

Everyone handles comments differently. Although it is always recommended to be direct and clear in your communication, there may be certain strategies you can adopt to communicate your comments effectively. If your employee has difficulties in achieving his goals, work with him and provide him with all the necessary help to improve his performance. The best way is to provide weekly or monthly comments to your employees, so they know what they must do to achieve their goals.

Provide Performance Support Technology

When faced with existing employees who do not meet expectations, it is a smart decision to offer them training (and / or training) and different resources to help them improve. As an example, you can combine a low-performance worker with someone to act as a mentor or offer you a manual with the procedures to follow. In addition, there are performance improvement tools: WalkMe is a very valuable technology that can help a worker be more efficient and precise, within the workflow (and not take them away from their daily tasks).

Offer rewards and recognition

Whenever you see that your employees have poor performance, it is always better to adopt a carrot and stick approach for instant and consistent improvement. It is a combination of rewards and punishments that you can induce for the best and worst weekly or monthly performance. This has proven to be one of the best ways to combat low performance problems in companies of all kinds for centuries.

Facing low-performance workers for the first time may not be too encouraging for managers as well, but having an adequate system to deal with them is essential, especially during the performance of change management. It is always better to deal with such situations, instead of ignoring them, to maintain the consistency of productivity and profitability in the business.

8 0
4 years ago
If the two 304-stainless-steel carriage bolts of the clamp each have a diameter of 10 mmmm, and they hold the cylinder snug with
S_A_V [24]

Answer: hello some data related to your question is missing attached below is the missing data

answer:

T2 = 265°C

Explanation:

First step : calculate sum of vertical forces

∑ y = 0

Fmg - 2(0.5 Fst ) = 0

∴Fmg = ( 12 * 10^6 ) ( 2 * π/4 (0.01)^2 )

          = 1884.96 N

Also determine the Compatibility equation in order to determine the change in Temperature

ΔT = 250°C

therefore Temperature at which average normal stress becomes 12.0 MPa

ΔT = T2 - T1

250°C = T2 - 15°C

T2 = 250 + 15 = 265°C

attached below is the detailed solution

4 0
3 years ago
A horizontal 2-m-diameter conduit is half filled with a liquid (SG=1.6 ) and is capped at both ends with plane vertical surfaces
luda_lava [24]

Answer:

Resultant force = 639 kN and it acts at 0.99m from the bottom of the conduit

Explanation:

The pressure is given as 200 KPa and the specific gravity of the liquid is 1.6.

The resultant force acting on the vertical plate, Ft, is equivalent to the sum of the resultant force as a result of pressurized air and resultant force due to oil, which will be taken as F1 and F2 respectively.

Therefore,

Ft = F1 + F2

According to Pascal's law which states that a change in pressure at any point in a confined incompressible fluid is transmitted throughout the fluid such that the same change occurs everywhere, the air pressure will act on the whole cap surface.

To get F1,

F1 = p x A

= p x (πr²)

Substituting values,

F1 = 200 x π x 1²

F1 = 628.32 kN

This resultant force acts at the center of the plate.

To get F2,

F2 = Π x hc x A

F2 = Π x (4r/3π) x (πr²/2)

Π - weight density of oil,

A - area on which oil pressure is acting,

hc - the distance between the axis of the conduit and the centroid of the semicircular area

Π = Specific gravity x 9.81 x 1000

Therefore

F2 = 1.6 x 9.81 x 1000 x (4(1)/3π) x (π(1)²/2)

F2 = 10.464 kN

Ft = F1 + F2

Ft = 628.32 + 10.464

Ft = 638.784 kN

The resultant force on the surface is 639 kN

Taking moments of the forces F1 and F2 about the centre,

Mo = Ft x y

Ft x y = (F1 x r) + F2(1 - 4r/3π)

Making y the subject,

y = (628.32 + 10.464(1 - 4/3π)/ 638.784

y = 0.993m

7 0
4 years ago
What is the function of the rotor and the stator in an AC motor
sweet-ann [11.9K]
The rotor is situated inside the stator and is mounted on the AC motor's shaft. It is the rotating part of the AC motor. And while we know this, the major function of the rotor and the stator is helping the motor shaft rotate.
7 0
4 years ago
Consider a cubic crystal with the lattice constant a. Complete the parts (a)-(c) below. (a) Sketch the crystallographic planes w
Anna [14]

Answer:

(a) See attachment

(b) The two planes are parallel because the intercepts for plane [220] are X = 0,5 and Y = 0,5 and for plane [110] are X = 1 and Y = 1. When the planes are drawn, they keep the same slope in a 2D plane.

(c) d = \frac{a}{\sqrt{h^{2} + k^{2} + l^{2}}} = \frac{1}{\sqrt{2}} =   0,707

Explanation:

(a) To determine the intercepts for an specific set of Miller indices, the reciprocal intercepts are taken as follows:

For [110]

X = \frac{1}{1} = 1; Y = \frac{1}{1} = 1; Z = \frac{1}{0} = \inf.

For [220]

X = \frac{1}{2} = 0,5;Y = \frac{1}{2} = 0,5;Z = \frac{1}{0} = \inf.

The drawn of the planes is shown in the attachments.

(b) Considering the planes as two sets of 2D straight lines with no intersection to Z axis, then the slope for these two sets are:

For (1,1):

K_1 = \frac{1}{1} = 1

For (0.5, 0.5):

K_2 = \frac{0.5}{0.5} = 1

As shown above, the slopes are exactly equal, then, the two straight lines are considered parallel and for instance, the two planes are parallel also.

(c) To calculate the d-spacing between these two planes, the distance is calculated as follows:

The Miller indices are already given in the statement. Then, the distance is:

\frac{1}{d^{2}} = \frac{h^{2} + k^{2} + l^{2}}{a^{2}}

d = \frac{a}{\sqrt{h^{2} + k^{2} + l^{2}}} = \frac{1}{\sqrt{2}} =   0,707

7 0
3 years ago
Other questions:
  • Consider an experiment in which the number of pumps in use at each of two seven-pump gas stations was determined. Call the two g
    10·1 answer
  • A stem and leaf display
    12·1 answer
  • 1. It is important that headings convey to the reader a. a sense of style. b. the relative importance of the parts of the paper.
    10·1 answer
  • RKI Instruments borrowed $4,800,000 from a private equity firm for expansion of its facility for manufacturing carbon monoxide m
    11·1 answer
  • At a certain location, wind is blowing steadily at 5 mph. Suppose that the mass density of air is 0.0796 lbm/ft3 and determine t
    6·1 answer
  • Please help <br>.. <br>....<br> . .<br>....<br>...​
    13·1 answer
  • Name four emerging technologies that could significantly impact how the construction industry conducts business.
    12·2 answers
  • Roundabouts have significantly lower crash and fatality rates than intersections.
    5·1 answer
  • 2. The moist weight of 0.1 ft3 of soil is 12.2 lb. If the moisture content is 12% and the specific gravity of soil solids is 2.7
    6·1 answer
  • If something is 50fficient, how many joules of wasted energy will there be if 750j of energy is put in?’
    12·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!