Ask question

Ask question

All categories

nataly862011 [7]

3 years ago

6

Select the correct statement(s) regarding frequency modulation (FM). a. baseband amplitude changes (information) are captured as

carrier wave frequency changes b. a device such as the voltage controlled oscillator (VCO) is required to convert signal amplitude changes to changes in frequency c. the more the carrier frequency is allowed to change (i.e., Δf), the greater the bandwidth as seen in the frequency domain d. all of the above are correct statements

1 answer:

mario62 [17]3 years ago

3 0

<h3>All of the above statement are correct statement.</h3>

<u>Explanation</u>

Base-Band amplitude changes are captured as carrier wave wave frequency changes. In order to convert signal amplitude changes to changes in frequency, we need a device like VCO.

The bandwidth in the frequency domain increases with the change in carrier frequency.

You might be interested in

In a short essay, discuss the question, "How are you an innovator?"

iragen [17]

Answer:

Being innovative means doing things differently or doing things that have never been done before. An innovator is someone who has embraced this idea and creates environments in which employees are given the tools and resources to challenge the status quo, push boundaries and achieve growth.

Explanation:

Hope it helps..

But it's a little bit long..

Correct me if I'm wrong..

7 0

3 years ago

Convert 250 lb·ft to N.m. Express your answer using three significant figures.

vfiekz [6]

Answer:

It will be equivalent to 338.95 N-m

Explanation:

We have to convert 250 lb-ft to N-m

We know that 1 lb = 4.45 N

So foe converting from lb to N we have to multiply with 4.45

So 250 lb = 250×4.45 =125 N

And we know that 1 feet = 0.3048 meter

Now we have to convert 250 lb-ft to N-m

So $250lb-ft=250\times 4.45N\times 0.348M=338.95N-m$

So 250 lb-ft = 338.95 N-m

6 0

3 years ago

Three tool materials (high-speed steel, cemented carbide, and ceramic) are to be compared for the same turning operation on a ba

Tpy6a [65]

Answer:

Among all three tools, the ceramic tool is taking the least time for the production of a batch, however, machining from the HSS tool is taking the highest time.

Explanation:

The optimum cutting speed for the minimum cost

$V_{opt}= \frac{C}{\left[\left(T_c+\frac{C_e}{C_m}\right)\left(\frac{1}{n}-1\right)\right]^n}\;\cdots(i)$

Where,

C,n = Taylor equation parameters

$T_h$ =Tool changing time in minutes

$C_e$ =Cost per grinding per edge

$C_m$ = Machine and operator cost per minute

On comparing with the Taylor equation $VT^n=C$ ,

Tool life,

$T= \left[ \left(T_t+\frac{C_e}{C_m}\right)\left(\frac{1}{n}-1\right)\right]}\;\cdots(ii)$

Given that,

Cost of operator and machine time $=\$40/hr=\$0.667/min$

Batch setting time = 2 hr

Part handling time: $T_h=2.5$ min

Part diameter: $D=73 mm$ $=73\times 10^{-3} m$

Part length: $l=250 mm=250\times 10^{-3} m$

Feed: $f=0.30 mm/rev= 0.3\times 10^{-3} m/rev$

Depth of cut: $d=3.5 mm$

For the HSS tool:

Tool cost is $20 and it can be ground and reground 15 times and the grinding= $2/grind.

So, $C_e=$ $\$20/15+2=\$3.33/edge$

Tool changing time, $T_t=3$ min.

$C= 80 m/min$

$n=0.130$

(a) From equation (i), cutting speed for the minimum cost:

$V_{opt}= \frac {80}{\left[ \left(3+\frac{3.33}{0.667}\right)\left(\frac{1}{0.13}-1\right)\right]^{0.13}}$

$\Rightarrow 47.7$ m/min

(b) From equation (ii), the tool life,

$T=\left(3+\frac{3.33}{0.667}\right)\left(\frac{1}{0.13}-1\right)\right]}$

$\Rightarrow T=53.4$ min

(c) Cycle time: $T_c=T_h+T_m+\frac{T_t}{n_p}$

where,

$T_m=$ Machining time for one part

$n_p=$ Number of pieces cut in one tool life

$T_m= \frac{l}{fN}$ min, where $N=\frac{V_{opt}}{\pi D}$ is the rpm of the spindle.

$\Rightarrow T_m= \frac{\pi D l}{fV_{opt}}$

$\Rightarrow T_m=\frac{\pi \times 73 \times 250\times 10^{-6}}{0.3\times 10^{-3}\times 47.7}=4.01 min/pc$

So, the number of parts produced in one tool life

$n_p=\frac {T}{T_m}$

$\Rightarrow n_p=\frac {53.4}{4.01}=13.3$

Round it to the lower integer

$\Rightarrow n_p=13$

So, the cycle time

$T_c=2.5+4.01+\frac{3}{13}=6.74$ min/pc

(d) Cost per production unit:

$C_c= C_mT_c+\frac{C_e}{n_p}$

$\Rightarrow C_c=0.667\times6.74+\frac{3.33}{13}=\$4.75/pc$

(e) Total time to complete the batch= Sum of setup time and production time for one batch

$=2\times60+ {50\times 6.74}{50}=457 min=7.62 hr$ .

(f) The proportion of time spent actually cutting metal

$=\frac{50\times4.01}{457}=0.4387=43.87\%$

Now, for the cemented carbide tool:

Cost per edge,

$C_e=$ $\$8/6=\$1.33/edge$

Tool changing time, $T_t=1min$

$C= 650 m/min$

$n=0.30$

(a) Cutting speed for the minimum cost:

$V_{opt}= \frac {650}{\left[ \left(1+\frac{1.33}{0.667}\right)\left(\frac{1}{0.3}-1\right)\right]^{0.3}}=363m/min$ [from(i)]

(b) Tool life,

$T=\left[ \left(1+\frac{1.33}{0.667}\right)\left(\frac{1}{0.3}-1\right)\right]=7min$ [from(ii)]

(c) Cycle time:

$T_c=T_h+T_m+\frac{T_t}{n_p}$

$T_m= \frac{\pi D l}{fV_{opt}}$

$\Rightarrow T_m=\frac{\pi \times 73 \times 250\times 10^{-6}}{0.3\times 10^{-3}\times 363}=0.53min/pc$

$n_p=\frac {7}{0.53}=13.2$

$\Rightarrow n_p=13$ [ nearest lower integer]

So, the cycle time

$T_c=2.5+0.53+\frac{1}{13}=3.11 min/pc$

(d) Cost per production unit:

$C_c= C_mT_c+\frac{C_e}{n_p}$

$\Rightarrow C_c=0.667\times3.11+\frac{1.33}{13}=\$2.18/pc$

(e) Total time to complete the batch $=2\times60+ {50\times 3.11}{50}=275.5 min=4.59 hr$ .

(f) The proportion of time spent actually cutting metal

$=\frac{50\times0.53}{275.5}=0.0962=9.62\%$

Similarly, for the ceramic tool:

$C_e=$ $\$10/6=\$1.67/edge$

$T_t-1min$

$C= 3500 m/min$

$n=0.6$

(a) Cutting speed:

$V_{opt}= \frac {3500}{\left[ \left(1+\frac{1.67}{0.667}\right)\left(\frac{1}{0.6}-1\right)\right]^{0.6}}$

$\Rightarrow V_{opt}=2105 m/min$

(b) Tool life,

$T=\left[ \left(1+\frac{1.67}{0.667}\right)\left(\frac{1}{0.6}-1\right)\right]=2.33 min$

(c) Cycle time:

$T_c=T_h+T_m+\frac{T_t}{n_p}$

$\Rightarrow T_m=\frac{\pi \times 73 \times 250\times 10^{-6}}{0.3\times 10^{-3}\times 2105}=0.091 min/pc$

$n_p=\frac {2.33}{0.091}=25.6$

$\Rightarrow n_p=25 pc/tool\; life$

So,

$T_c=2.5+0.091+\frac{1}{25}=2.63 min/pc$

(d) Cost per production unit:

$C_c= C_mT_c+\frac{C_e}{n_p}$

$\Rightarrow C_c=0.667\times2.63+\frac{1.67}{25}=$1.82/pc$

(e) Total time to complete the batch

$=2\times60+ {50\times 2.63}=251.5 min=4.19 hr$ .

(f) The proportion of time spent actually cutting metal

$=\frac{50\times0.091}{251.5}=0.0181=1.81\%$

3 0

4 years ago

An engineer is testing the shear strength of spot welds used on a construction site. The engineer's null hypothesis at a 5% leve

lilavasa [31]

Answer:

b) The null hypothesis should be rejected.

Explanation:

The null hypothesis is that the mean shear strength of spot welds is at least

3.1 MPa

H0: u ≥3.1 MPa against the claim Ha: u< 3.1 MPa

The alternate hypothesis is that the mean shear strength of spot welds is less than 3.1 MPa.

This is one tailed test

The critical region Z(0.05) < ± 1.645

The Sample mean= x`= 3.07

The number of welds= n= 15

Standard Deviation= s= 0.069

Applying z test

z= x`-u/s/√n

z= 3.07-3.1/0.069/√15

z= -0.03/0.0178

z= -1.68

As the calculated z= -1.68 falls in the critical region Z(0.05) < ± 1.645 the null hypothesis is rejected and the alternate hypothesis is accepted that the mean shear strength of spot welds is less than 3.1 MPa

8 0

3 years ago

GG(ss) = 1 ss2 + 3 We want to design a feedback control system in a unity feedback structure by adding a controller DD(ss) = ss+

saw5 [17]

Answer:

Explanation:

The explanation is given in the picture that is shown below

3 0

3 years ago