All categories

3 years ago

1. The correct way to use a seat belt is

Computers and Technology

1 answer:

Nesterboy [21]3 years ago

4 0

Answer:

4 steps

Explanation:

Step 1: Pull belt across body

Sit in any of your vehicle's seats and secure the three-point harness in its buckle by pulling it across your body.

If the seatbelt is too short, consider an aftermarket restraint and extender. Make sure they meet federal safety standards and are installed professionally.

Step 2: Adjust lower belt

Adjust the lower belt snuggly across your lap and pelvis area – never your stomach.

Pregnant women should wear the lap belt below their belly, not on or above it.

Step 3: Adjust shoulder belt

Adjust the shoulder belt to fit comfortably across the collarbone and chest. It should never rub on your neck or face. Never put the shoulder belt behind your back or under your arm.

Step 4: Check before driving

Check that the belt is secure before driving.

You might be interested in

____ is the encapsulation of method details within a class.

Anestetic [448]

Implementation hiding i<u>s the encapsulation of method details within a class</u>. Implementation can be interpreted as those specifications which can be altered without altering the correctness of an application. Wrapping data/methods within classes (descriptions of the way all objects of this type will look/act) in combination with implementation hiding is called encapsulation. Information users need to know about behaviors should be available without dependence on implementation specifications.

6 0

3 years ago

Que cambiaría personalmente en esos momentos de cuarentena

Natali5045456 [20]

No poder salir sin estar con la duda de que si una persona con la que estas cercas tendría el virus , no poder visitar a ciertas personas

6 0

3 years ago

Suppose that a 64MB system memory is built from 64 1MB RAM chips. How many address lines are needed to select one of the memory

alexdok [17]

Answer:

6 address lines

Explanation:

The computation of the number of address lines needed is shown below:

Given that

Total memory = 64MB

= $2^6MB$

= $2^{26} bytes$

Also we know that in 1MB RAM the number of chips is 6

So, the number of address lines is $2^{26} address$ i..e 26 address lines

And, the size of one chip is equivalent to 1 MB i.e. $2^{20} bytes$

For a single 1MB chips of RAM, the number of address lines is

$\frac{2^{26}}{2^{20}} \\\\= 2^6 address$

Therefore 6 address lines needed

5 0

3 years ago

Case Project 9-4: Troubleshoot an IP configurationYou work at a help desk and have just received a call from an employee who say

Svetllana [295]

Answer:

To get the IP address and other information on the workstation, type 'ipconfig' for windows or 'ifconfig' or Linux and press the return key.

The subnet mask is a class B type and 169.254.14.11 IP address shows that the workstation cannot access the DHCP server, so the IP address is not properly configured for network connection.

Explanation:

A computer network is an interconnection and intercommunication of two or more computer devices. All devices in a network must have an IP address, which can be static or dynamic from a DHCP server.

When a computer is configured to receive IP address from a DHCP server, but cannot reach the server, the IP address from the range of 169 is automatically assigned to it but still would not be able to communicate with other devices in the network.

4 0

2 years ago

I know this isn't a school question but it is important! how do I get out of hp hardware diagnostics UEFI on hp pc? (step by ste

Debora [2.8K]

Answer:

1. Turn off the computer and wait five seconds.

2. Press the Power button to start the computer and repeatedly press the F10 key to enter the BIOS setup menu.

3. On the BIOS Setup screen, press F9 to select and load the BIOS Setup Default settings.

4. Press F10 to Save and Exit.

5. Use the arrow keys to select Yes, then press Enter when asked Exit Saving Changes?

6. Follow the prompts to restart your computer.

After you have get to the operating system,

1. Press CTRL + Alt + Del on the blank screen.

2. Click on Task Manager

3. Click "File" - "Run a new task" If there is no "file" option, please click on the task manager under the "details"

4. In the pop-up window, enter "msconfig" click "OK"

5. In the system configuration window that appears, click "Service" and uncheck "App Readiness".

6. Click "Apply" --- "OK"

7. In the following window appears to click on the "restart"

6 0

3 years ago