All categories

3 years ago

Which of the following are the main psychological domains?

Engineering

1 answer:

Alexeev081 [22]3 years ago

7 0

Answer:

Domain 1: Biological (includes neuroscience, consciousness, and sensation) Domain 2: Cognitive (includes the study of perception, cognition, memory, and intelligence) Domain 3: Development (includes learning and conditioning, lifespan development, and language) i hope this helps you.

You might be interested in

Why is the back-work ratio much higher in the brayton cycle than in the rankine cycle?

zloy xaker [14]

The back-work ratio much higher in the Brayton cycle than in the Rankine cycle because a gas cycle is the Brayton cycle, while a steam cycle is the Rankine cycle. Particularly, the creation of water droplets will be a constraint on the steam turbine's efficiency. Since gas has a bigger specific volume than steam, the compressor will have to work harder while using gas.

<h3>What are modern Brayton engines?</h3>

Even originally Brayton exclusively produced piston engines, modern Brayton engines are virtually invariably of the turbine variety. Brayton engines are also gas turbines.

<h3>What is the ranking cycle?</h3>

A gas cycle is the Brayton cycle, while the Ranking cycle is a steam cycle. The production of water droplets will especially decrease the steam turbine's performance. Gas-powered compressors will have to do more work since gas's specific volume is greater than steam's.

To know more about Rankine cycle, visit: brainly.com/question/13040242

#SPJ4

4 0

1 year ago

Calculate the pressure drop in a duct (measured by a differential oil manometer) if the differential height between the two flui

Burka [1]

Answer:

The pressure drop is 269.7N/m^2

Explanation:

∆P = ∆h × rho × g

∆h = 3.2cm = 3.2/100 = 0.032m, rho = 860kg/m^3, g = 9.8m/s^2

∆P = 0.032×860×9.8 = 269.7N/m^2

6 0

3 years ago

What are the advantages and disadvantages of a mine heardgear

Irina18 [472]

Answer:

If there is a shaft with headgear, then mining can take place until that depth of the shaft. If it is accessed horizontal Adits, it can mine until the lowest Adit from upwards. If it is accessed decline, the development and mining can continue so long as economic exploitation is possible.

Explanation:

What are the disadvantages of mining headgear? They totally cut off your vision of anything above your head. They are hot, most of the time

7 0

2 years ago

A 4-pole, 60-Hz, 690-V, delta-connected, three-phase induction motor develops 20 HP at full-load slip of 4%. 1) Determine the to

gladu [14]

Answer:

1. i. 20 Nm ii. 4.85 HP

2. 16.5 %

Explanation:

1) Determine the torque and the power developed at 4% slip when a reduced voltage of 340V is applied.

i. Torque

Since slip is constant at 4 %,torque, T ∝ V² where V = voltage

Now, T₂/T₁ = V₂²/V₁² where T₁ = torque at 690 V = P/2πN where P = power = 20 HP = 20 × 746 W = 14920 W, N = rotor speed = N'(1 - s) where s = slip = 4% = 0.04 and N' = synchronous speed = 120f/p where f = frequency = 60 Hz and p = number of poles = 4.

So, N' = 120 × 60/4 = 30 × 60 = 1800 rpm

So, N = N'(1 - s) = 1800 rpm(1 - 0.04) = 1800 rpm(0.96) = 1728 rpm = 1728/60 = 28.8 rps

So, T = P/2πN = 14920 W/(2π × 28.8rps) = 14920 W/180.96 = 82.45 Nm

T₂ = torque at 340 V, V₁ = 690 V and V₂ = 340 V

So, T₂/T₁ = V₂²/V₁²

T₂ = (V₂²/V₁²)T₁

T₂ = (V₂/V₁)²T₁

T₂ = (340 V/690 V)²82.45 Nm

T₂ = (0.4928)²82.45 Nm

T₂ = (0.2428)82.45 Nm

T₂ = 20.02 Nm

T₂ ≅ 20 Nm

ii. Power

P = 2πT₂N'

= 2π × 20 Nm × 28.8 rps

= 1152π W

= 3619.11 W

converting to HP

= 3619.11 W/746 W

= 4.85 HP

2) What must be the new slip for the motor to develop the same torque when the reduced voltage is applied

Since torque T ∝ sV² where s = slip and V = voltage,

T₂/T₁ = s₂V₂²/s₁V₁²

where T₁ = torque at slip, s₁ = 4% and voltage V₁ = 690 V and T₂ = torque at slip, s₂ = unknown and voltage V₂ = 340 V

If the torque is the same, T₁ = T₂ ⇒ T₂T₁ = 1

So,

T₂/T₁ = s₂V₂²/s₁V₁²

1 = s₂V₂²/s₁V₁²

s₂V₂² = s₁V₁²

s₂ = s₁V₁²/V₂²

s₂ = s₁(V₁/V₂)²

substituting the values of the variables into the equation, we have

s₂ = s₁(V₁/V₂)²

s₂ = 4%(690/340)²

s₂ = 4%(2.0294)²

s₂ = 4%(4.119)

s₂ = 16.47 %

s₂ ≅ 16.5 %

3 0

3 years ago

Use Excel, MatLab or a similar program to plot carrier thermal velocity as a function of temperature for both electrons and hole

Sidana [21]

Answer:

Solution 2:

The thermal energy of any particle is given as = $\frac{1}{2}mv^{2}$

where m= Effective mass of the particle,

v= Velocity of the particle

The average kinetic energy is given as = $\frac{3}{2}KT,$

where K= Boltzmann Constant

T= Temperautre of the particle

At equilibrium,

1/2 mv² = 3/2 KT

Hence, v= $\sqrt{\frac{3KT}{m}}$

As, effective mass ratio is calculated with respect to rest mass of electron,

melectron = 0.11 * 9.11 *10-31 kg

mhole = 0.35 *9.11 *10-31 kg

K = 1.38 × 10-23 m2 kg s-2 K-1

Plotting, over a range of temperature of 0 K to 400 K, we obtain the attached Graphs (attached).

Solution 3:

The above two curves plotted are not identical as seen. From the same value of Temperature, and under identical conditons, the Thermal velocity solely depends on effective mass ratio. And it is inversely proportional to effective mass ratio. More the effective mass ratio, less the thermal velocity and flatter the slope of the curve and vice versa. As, the mass ratio of holes is more than that of electrons, the curve of electrons has a steeper slope than that of holes. Hence, the curves are not just identical.

8 0

3 years ago