All categories

2 years ago

Draw isometric projection of a pls help

Engineering

1 answer:

Genrish500 [490]2 years ago

8 0

Draw isometric projection Spatial axes of the item are represented as similarly willing to the drawing floor and same distances alongside the axes are drawn the same.

<h3>What is isometric projection?</h3>

Definition of isometric projection an axonometric projection wherein the 3 spatial axes of the item are represented as similarly willing to the drawing floor and same distances alongside the axes are drawn same.

An isometric view of an item may be received via way of means of selecting the viewing path such that the angles among the projections of the x, y, and z axes are all of the same, or 120°. For example, with a cube, that is achieved via way of means of first searching immediately toward one face.

You might be interested in

Various factors to be considered in deciding the factor of safety?

Eduardwww [97]

Answer with Explanation:

There are various factors that needed to be taken into account while deciding the factor of safety some of which are summarized below as:

1) Importance of the structure: When we design any structure different structures have different importance in our society. Take an example of hospital, in case a natural disaster struck's a place the hospital should be the designed to withstand the disaster as it's role in the crisis management following a disaster is well understood. Thus while designing it we need it to have a higher factor of safety against failure when compared to a local building.

2) Errors involved in estimation of strength of materials: when we design any component of any machine or a structure we need to have an exact idea of the behavior of the material and know the value of the strength of the material. But many materials that we use in structure such as concrete in buildings have a very complex behavior and we cannot estimate the strength of the concrete absolutely, thus we tend to decrease the strength of the concrete more if errors involved in the estimation of strength are more to give much safety to the structure.

3) Variability of the loads that may act on the structure: If the loads that act on the structure are highly variable such as earthquake loads amd dynamic loads then we tend to increase the factor of safety while estimating the loads on the structure while designing it.

4) Economic consideration: If our project has abundant funds then we can choose a higher factor of safety while designing the project.

4 0

3 years ago

I will give Brainliest, please help. :)

ziro4ka [17]

Answer:

The ratio of water to flour needed to make tortillas, which is 3 : 4

Explanation:

100 w = 75 f

w/f = 75/100 = 3/4

7 0

3 years ago

Read 2 more answers

a. Determine R for a series RC high-pass filter with a cutoff frequency (fc) of 8 kHz. Use a 100 nF capacitor. b. Draw the schem

Readme [11.4K]

Answer:

a) 199.04 ohms

b) attached in image

c) -0.696dB

Explanation:

We are given:

Fc = 8Khz = 8000hz

$C = 100nF = 100*10^-^9F$

a)Using the formula:

$F_c = \frac{1}{2pie*Rc}$

$8000= \frac{1}{2*3.14*R*100*10^-^9}$

$R =\frac{1}{2*3.14*100*10^-^9*8000}$

R = 199.04 ohms

b) diagram is attached

c) $H(w) = \frac{V_out(w)}{Vin(w)} = \frac{1}{1-j\frac{wc}{w}}$

$H(F) = \frac{1}{1-j\frac{fc}{f}}$

At F = 20KHz and Fc= 8KHz we have:

$H(F)= \frac{1}{1-j\frac{8}{20}} = \frac{1}{1-j(0.4)}$

$|H(F)|= \frac{1}{\sqrt{1^2+(0.4)^2}}$

=0.923

|H(F)| in dB = 20log |H(F)|

=20log0.923

= -0.696dB

5 0

3 years ago

All circuits need three basic parts: an energy source, wires, and the object that is going to change the electrical energy into

Radda [10]

load every electric circuit,regardless of where it is or how large or small, has four basic parts: an energy source (ac or dc),a conductor (wire), an electrical load (device), and at least one controller(switch)

7 0

4 years ago

Read 2 more answers

Water flows with a velocity of 3 m/s in a rectangular channel 3 m wide at a depth of 3 m. What is the change in depth and in wat

strojnjashka [21]

Answer: new depth will be 3.462m and the water elevation will be 0.462m.

The maximum contraction will be achieved in width 0<w<3

Explanation:detailed calculation and explanation is shown in the image below

8 0

3 years ago