1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
atroni [7]
3 years ago
5

26 points!!

Engineering
1 answer:
Alexandra [31]3 years ago
8 0
Answer:
Tesla switched to smaller front motors to permanent magnets on the model S and X after seeing the mileage results of model 3 permanent magnet motors.

The model 3 got more mileage but they make their money by keeping people coming back for a new car after their mileage runs out.

So they switched to a less quality standard model.
You might be interested in
If the driver gear has 5 teeth and the driven gear has 10 teeth,what is the gear ratio?​
shepuryov [24]
The on that has ten teeth
6 0
3 years ago
Read 2 more answers
The ampere draw of a 5000 watt electric heater used on 120 volts is
Salsk061 [2.6K]

Answer:

41.67amps

Explanation:

v*a=w

120*a=5000

5000/12=41.67

8 0
4 years ago
Interpret the Blame responsibility and causation in your own words in the light of Columbia Accident.
Licemer1 [7]

Answer:

Proposed Improvements and Generic Lessons

Within 2 h of losing the signal from the returning spacecraft, NASA’s Administrator established the Columbia Accident Investigation Board (CAIB) to uncover the conditions that had produced the disaster and to draw inferences that would help the US space program to emerge stronger than before (CAIB, 2003). Seven months later, the CAIB released a detailed report that included its recommendations (Starbuck and Farjoun, 2005).

The CAIB (2003) report attempted to seek answers to the following four crucial questions:

1.

Why did NASA continue to launch spacecraft despite many years of known foam debris problems?

2.

Why did NASA managers conclude, despite the concerns of their engineers, that the foam debris strike was not a threat to the safety of the mission?

3.

How could NASA have forgotten the lessons of Challenger?

4.

What should NASA do to minimize the likelihood of such accidents in the future?

Although the CAIB’s comprehensive report raised important questions and offered answers to some of them, it also left many major questions unanswered (Starbuck and Farjoun, 2005).

1.

Why did NASA consistently ignore the recommendations of several review committees that called for changes in safety organization and practices?

2.

Did managerial actions and reorganization efforts that took place after the Challenger disaster contribute, both directly and indirectly, to the Columbia disaster?

3.

Why did NASA’s leadership fail to secure more stable funding and to shield NASA’s operations from external pressures?

By examining, with respect to the Columbia disaster, the case of NASA as an organization, one can try to extract generalizations that could be useful for other organizations, especially those engaged in high-risk activities—such as nuclear power plants, oil and gas, hospitals, airlines, armies, and pharmaceutical companies—and such generic principles may also be salutary for any kind of organization.

The CAIB (2003) report recommended developing a plan to inspect the condition of all RCC systems, the investigation having found the existing inspection techniques to be inadequate. RCC panels are installed on parts of the shuttle, including the wing leading edges and nose cap, to protect against the excessive temperatures of reentry. They also recommended that taking images of each shuttle while in orbit should be standard procedure as well as upgrading the imaging system to provide three angles of view of the shuttle, from liftoff to at least SRB separation. “The existing camera sites suffer from a variety of readiness, obsolescence, and urban encroachment problems.” The board offered this suggestion because NASA had had no images of the Columbia shuttle clear enough to determine the extent of the damage to the wing. They also recommended conducting inspections of the TPS, including tiles and RCC panels, and developing action plans for repairing the system. The report included 29 recommendations, 15 of which the board specified must be completed before the shuttle returned to flight status, and also made 27 “observations” (CAIB, 2005).

7 0
3 years ago
The atomic radii of a divalent cation and a monovalent anion are 0.77 nm and 0.136 nm, respectively.1- Calculate the force of at
MrMuchimi

Answer:

A) attractive force between ions = 5.09x10^-19 N of attractive force

B) there will be no repulsion since both ions have opposite charges.

Explanation:

Detailed explanation and calculation is shown in the image below.

5 0
4 years ago
Why do electricians require critical thinking skills? In order to logically identify alternative solutions to problems in order
Rina8888 [55]

Answer:

In order to logically identify alternative solutions to problems

Explanation:

Electricians are specialized in electrical wiring of buildings, transmission lines, stationary machines, and related equipment. They are either employed in the installations of new electrical components, or to maintain an already installed component. The job of an electrician can be mentally tasking, especially in troubleshooting for fault, and methods of fixing of faults. Some problems might require an out-of-norm approach to solve, and the electrician has to be able to logically identify alternative solutions to problems.

8 0
3 years ago
Other questions:
  • Which statement about tensile stress is true? A. Forces that act perpendicular to the surface and pull an object apart exert a t
    9·1 answer
  • In a steady-flow industrial process, m kg/s of an ideal gas flows through a heater at a constant mass flow rate. It is your job
    7·1 answer
  • The yield strength of mild steel is 150 MPa for an average grain diameter of 0.038 mm ; yield strength is 250 MPa for average gr
    15·1 answer
  • The displacement of an oscillating mass is 0.004*sin(7t) meters. What is the peak amplitude of its velocity in meters/second?
    10·1 answer
  • Match the car part to the system
    7·1 answer
  • Weight limit for a pallet
    15·2 answers
  • Thanks for the help!
    11·1 answer
  • Technician A says that a graphing multi-meter may be used to verify signals going to and from electrical and electronic componen
    9·1 answer
  • Type the correct answer in the box. Spell all words correctly. Type the exact term Mike should use for the given scenario. Mike
    8·2 answers
  • Who do you contact to get your credit report?
    13·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!