1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
Ugo [173]
3 years ago
15

A ten story hospital has to constructed with the footprint of 45,000 ft^2. Subsurface soil consist of soft clay layer of 10 ft.

Deep pile foundation will be used for supporting the building. The depth of pile foundation will be the 15ft.
Required:
a. Determine number of the boring to be used for the subsurface investigation using NYC Code Mandate discussed in the class.
b. Also determine the depth of the boring to be used for subsurface investigation.
Engineering
1 answer:
givi [52]3 years ago
4 0

Answer:

a) approximately, the number of bores to be used is 17

b) depth of the boring is 25 ft from ground level

Explanation:

Given the data in the question;

we know that; The New York City Code mandate; deep foundation clause Number 1802.4.1  states that required number of borings shall not be less than two boring

i.e  a minimum Number of 1 boring per 2000 square foot for the first 20,000 square foot and one boring per every additional 4000 square foot

so;

number of the boring to be used for the subsurface investigation using NYC Code Mandate will be;

⇒ 20,000/2000 + [( 45,000 - 2000)/4000]

= 10 + 6.25

= 16.25 ≈ 17

approximately, the number of boring to be used is 17

b)

the depth of the boring to be used for subsurface investigation will be;

⇒ 10 ft + 15 ft

= 25 ft

Therefore, depth of the boring is 25 ft from ground level

You might be interested in
A two-bus power system is interconnected by one transmission line. Bus 1 is a generator bus with specified terminal voltage magn
mixas84 [53]

Answer:

a) | v2 | ,  β2   ( load, bus voltage at bus 2 )

  p1 ,  q1 ( slack, bus power at bus 1 )

b) q2 , β2  

  p1 and q1 ( slack, bus power at bus 1 )

Explanation:

Attached below is a schematic representation of the solution

<u>a) Identify the variables in the solution vector assume Bus 2 is a load bus</u>

The specified parameters are ; P2 and q2

while | v2 | and β2 are not specified

given that bus 2 is a load bus, bus 1 is a slack bus with ; | v1 |  and β1 been specified while p1 and q1 are not specified

<em>Hence the variables in the solution </em>

<em>= | v2 | ,  β2   ( load, bus voltage at bus 2 )</em>

<em>   p1 ,  q1 ( slack, bus power at bus 1 ) </em>

<u>b) Identify the variables in the solution vector ( assume Bus 2 is a PV bus )</u>

specified at Bus 2 are ; | p2 | , | v2 |

unspecified : q2 , β2

Bus 1 ( still a slack bus )

specified parameter : | v1 |  and β1

unspecified : p1 and q1

<em>Hence the variables in the solution </em>

<em>= q2 , β2  </em>

<em>   p1 and q1 ( slack, bus power at bus 1 ) </em>

7 0
3 years ago
An unknown relative passes away and bequeaths upon you a small tract of land in Amherst. You decide to build a two-story storage
Ratling [72]

Answer: It does make sense, because I've been involved in these careers and have a long family line of them. And other questions?

Explanation:

7 0
3 years ago
Whatever they said bbbbbbbbbbbbbbbbbb
solong [7]

Answer:

yh and I said aaaaaaaaaaaa

Explanation:

7 0
3 years ago
Read 2 more answers
Independent auto lots usually have ____ finance rates than dealerships
wel

Independent auto lots usually have <u>higher</u> finance rates than dealerships

<u>Explanation:</u>

The finance rates that are charged by the dealers are lower than the finance charges that are charged by the independent auto. In case if you are getting financed through dealerships, you can also negotiate with them to charge finance rates and lower the charges of the finance.

But this negotiation and lowering of the finance rates is not possible with the independent auto lots and thus they charge higher rates compared to the dealerships.

8 0
3 years ago
1. Consider a city of 10 square kilometers. A macro cellular system design divides the city up into square cells of 1 square kil
kakasveta [241]

Answer:

a) n = 1000\,users, b)\Delta t_{min} = \frac{1}{30}\,h, \Delta t_{max} = \frac{\sqrt{2} }{30}\,h, \Delta t_{mean} = \frac{1 + \sqrt{2} }{60}\,h, c) n = 10000000\,users, \Delta t_{min} = \frac{1}{3000}\,h, \Delta t_{max} = \frac{\sqrt{2} }{3000}\,h, \Delta t_{mean} = \frac{1 + \sqrt{2} }{6000}\,h

Explanation:

a) The total number of users that can be accomodated in the system is:

n = \frac{10\,km^{2}}{1\,\frac{km^{2}}{cell} }\cdot (100\,\frac{users}{cell} )

n = 1000\,users

b) The length of the side of each cell is:

l = \sqrt{1\,km^{2}}

l = 1\,km

Minimum time for traversing a cell is:

\Delta t_{min} = \frac{l}{v}

\Delta t_{min} = \frac{1\,km}{30\,\frac{km}{h} }

\Delta t_{min} = \frac{1}{30}\,h

The maximum time for traversing a cell is:

\Delta t_{max} = \frac{\sqrt{2}\cdot l }{v}

\Delta t_{max} = \frac{\sqrt{2} }{30}\,h

The approximate time is giving by the average of minimum and maximum times:

\Delta t_{mean} = \frac{1+\sqrt{2} }{2}\cdot\frac{l}{v}

\Delta t_{mean} = \frac{1 + \sqrt{2} }{60}\,h

c) The total number of users that can be accomodated in the system is:

n = \frac{10\times 10^{6}\,m^{2}}{100\,m^{2}}\cdot (100\,\frac{users}{cell} )

n = 10000000\,users

The length of each side of the cell is:

l = \sqrt{100\,m^{2}}

l = 10\,m

Minimum time for traversing a cell is:

\Delta t_{min} = \frac{l}{v}

\Delta t_{min} = \frac{0.01\,km}{30\,\frac{km}{h} }

\Delta t_{min} = \frac{1}{3000}\,h

The maximum time for traversing a cell is:

\Delta t_{max} = \frac{\sqrt{2}\cdot l }{v}

\Delta t_{max} = \frac{\sqrt{2} }{3000}\,h

The approximate time is giving by the average of minimum and maximum times:

\Delta t_{mean} = \frac{1+\sqrt{2} }{2}\cdot\frac{l}{v}

\Delta t_{mean} = \frac{1 + \sqrt{2} }{6000}\,h

8 0
4 years ago
Other questions:
  • The ratio of the weight of a substance to the weight of equal volume of water is known as a) Density b) specific gravity c) spec
    8·1 answer
  • You want to determine whether the race of the defendant has an impact on jury verdicts. You assign participants to watch a trial
    9·1 answer
  • You are to assess the biomechanics of a male’s arm using his bicep to hold a 20 kg object in his hand. The upper arm is perpendi
    5·1 answer
  • Consider 1.0 kg of austenite containing 1.15 wt% C, cooled to below 727C (1341F). (a) What is the proeutectoid phase? (b) How
    14·1 answer
  • For problems 1 and 2, six luminaires, similar to Style E used in the Commercial Building, are to be installed in a room that is
    13·1 answer
  • The heat transfer rate per unit area in a thermal circuit is equivalent to what quantity in an electric circuit? A. voltage B. c
    6·1 answer
  • A steady state filtration process is used to separate silicon dioxide (sand) from water. The stream to be treated has a flow rat
    5·1 answer
  • Your friend has two substances A and B which are compressed liquid and superheated vapor respectively. Both are in rigid vessels
    15·1 answer
  • I want to solve the question
    11·1 answer
  • Derive the expression ε=ln(1+e), where ε is the true strain and e is the engineering strain. Note that this expression is not va
    14·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!