Ask question

Ask question

All categories

4 years ago

12

In architectural drawings, what do architects use to convey exact details about various parts of a drawing without leaving any s

cope for misinterpretation?

2 answers:

il63 [147K]4 years ago

8 0

Architects use
marks to identify the exact parts of a building without leaving any scope for misinterpretation.

RideAnS [48]4 years ago

8 0

Answer:

Architects use reference marks

Explanation:

You might be interested in

What is future active and future passive and future perfect active

san4es73 [151]

The future perfect tense forms are made by putting ‘will / shall + have’ before the past participle from the verb. these sentences can be changed into the passive if the active verb has an object

i hope this helps :D thanks

5 0

3 years ago

The substance called olivine may have any composition between Mg2SiO4 and Fe2SiO4, i.e. the Mg atoms can be replaced by Fe atoms

Ipatiy [6.2K]

Answer:

The answer is "0.147 nm and 99.63 mol %"

Explanation:

In point (a):

$\to nk1 = 062$

$\to \text{Bragg angle}$ $\theta =37.21^{\circ}$

$\to \text{diffraction angle}$ $2 \theta = 74.42^{\circ}$

$\to \lambda = 0.1790 nm$

find:

d(062)=?

formula:

$\to nx = 2d \sin \theta$

$\to d(062) = \frac{1 \times 0.1790^{\circ}}{2 \times \sin 37.21^{\circ}}\\$

$= \frac{0.1790^{\circ}}{2 \times 0.604738126}\\\\= \frac{0.29599589}{2}\\\\= 0.147 \\$

In point (b):

$\to Mg_2SiO_4\longleftrightarrow Fe_2SiO_4$

$d= 0.14774 \ \ \ \ \ olivine = 0.147 \ \ \ \ \ 0.15153$

formula:

$\to d=\frac{a}{\sqrt{n^2+k^2+i^2}}\\$

that's why the composition value equal to 99.63 %

3 0

3 years ago

In a TDM communication example, 15 voice signals are badlimited to 5kHz and transmitted simultaneously using PAM. What is a prel

MA_775_DIABLO [31]

Answer:

Option D

160 kHz

Explanation:

Since we must use at least one synchronization bit, total message signal is 15+1=16

The minimum sampling frequency, fs=2fm=2(5)=10 kHz

Bandwith, BW required is given by

BW=Nfs=16(10)=160 kHz

5 0

4 years ago

A non-inductive load takes a current of 15A at 125V. An inductor is then connected in series in order that the same current shal

Norma-Jean [14]

Answer:

The inductance of the inductor is 0.051H

Explanation:

From Ohm's law;

V = IR .................. 1

The inductor has its internal resistance referred to as the inductive reactance, X $_{L}$ , which is the resistance to the flow of current through the inductor.

From equation 1;

V = IX $_{L}$

X $_{L}$ = $\frac{V}{I}$ ................ 2

Given that; V = 240V, f = 50Hz, $\pi$ = $\frac{22}{7}$ , I = 15A, so that;

From equation 2,

X $_{L}$ = $\frac{240}{15}$

= 16Ω

To determine the inductance of the inductor,

X $_{L}$ = 2 $\pi$ fL

L = $\frac{X_{L} }{2 \pi f}$

= $\frac{16}{2*\frac{22}{7}*50 }$

= 0.05091

The inductance of the inductor is 0.051H.

4 0

4 years ago

Calculate the areas under the stress-strain curve (toughness) for the materials shown in Fig. below, (a) plot them as a

defon

Answer:

Explanation:

Wow

5 0

3 years ago