If the total mechanical energy of a swinging pendulum is 75 J,

in the derivation of the time period of a pendulum in electric field when considering the fbd of bob to find the g effective why

Neko [114]

Answer:

we learned that an object that is vibrating is acted upon by a restoring force. The restoring force causes the vibrating object to slow down as it moves away from the equilibrium position and to speed up as it approaches the equilibrium position. It is this restoring force that is responsible for the vibration. So what forces act upon a pendulum bob? And what is the restoring force for a pendulum? There are two dominant forces acting upon a pendulum bob at all times during the course of its motion. There is the force of gravity that acts downward upon the bob. It results from the Earth's mass attracting the mass of the bob. And there is a tension force acting upward and towards the pivot point of the pendulum. The tension force results from the string pulling upon the bob of the pendulum. In our discussion, we will ignore the influence of air resistance - a third force that always opposes the motion of the bob as it swings to and fro. The air resistance force is relatively weak compared to the two dominant forces.

The gravity force is highly predictable; it is always in the same direction (down) and always of the same magnitude - mass*9.8 N/kg. The tension force is considerably less predictable. Both its direction and its magnitude change as the bob swings to and fro. The direction of the tension force is always towards the pivot point. So as the bob swings to the left of its equilibrium position, the tension force is at an angle - directed upwards and to the right. And as the bob swings to the right of its equilibrium position, the tension is directed upwards and to the left. The diagram below depicts the direction of these two forces at five different positions over the course of the pendulum's path.

that's what I know so far

8 0

3 years ago

What is the current through a 25 ohm resistor connected to a 5.0 V power supply? a 0.20 A b 5.0 A c 25 A d 30 A

zysi [14]

~Formula: Voltage= current• resistance
(V= Ir)
~Using this formula, plug in the numbers from the equation into the formula
~5=25i
~Now you have a one-step equation
~Divide by 25 on both sides and you should get your answer:
~I= 0.2 (which means current is 0.2)

8 0

3 years ago

Which formulas have been correctly rearranged to solve for radius? Check all that apply. r = GM central/v^2 r =fcm/v^2 r =ac/v^2

jek_recluse [69]

The orbital radius is: $r=\frac{GM}{v^2}$

Explanation:

The problem is asking to find the radius of the orbit of a satellite around a planet, given the orbital speed of the satellite.

For a satellite in orbit around a planet, the gravitational force provides the required centripetal force to keep it in circular motion, therefore we can write:

$\frac{GMm}{r^2}=m\frac{v^2}{r}$

where

G is the gravitational constant

M is the mass of the planet

m is the mass of the satellite

r is the radius of the orbit

v is the speed of the satellite

Re-arranging the equation, we find:

$\frac{GM}{r}=v^2\\r=\frac{GM}{v^2}$

Learn more about circular motion:

brainly.com/question/2562955

brainly.com/question/6372960

#LearnwithBrainly

7 0

3 years ago

Read 2 more answers

an object is acted on by a drag force with a magnitude that is proportional to the speed. the object accelerates downward at 3.0

Nutka1998 [239]

The terminal speed of the object falling down is 66.67 m/s.

The terminal speed acquired by the body when,

Weight of the body = Drag force of the body

It is given,

Drag force is directly proportional to the speed,

So,

F = CV

Where F is drag force,

V is the speed,

C is the constant,

So, it can be written as C = F/V.

The weight of the body = mg

The weight of the body = 10m

M is the mass and g is the acceleration due to gravity,

The drag force when the speed is 20m/s.

Drag force = ma

a is the acceleration during the drag force which is given to be 3m/s²,

Drag force = 3m

Now we can write,

F₁/V₁ = F₂/V₂

F₁ is the drag force at 20m/s speed.

F₂ is the weight of the body and V₂ is the terminal speed,

Now, it can be written,

3m/20 = 10m/V₂

V₂ = 66.67 m/s.

So, the terminal speed is 66.67m/s.

To know more about terminal speed, visit,

brainly.com/question/14605362

#SPJ4

7 0

1 year ago

What is the term used to describe the energy needed to get a reaction started

olganol [36]

Activation Energy is the amount of energy needed to get a reaction started.

3 0

3 years ago