All categories

3 years ago

Hii

1 answer:

8 0

Answer:Make an small diy holder that has heat packs keeping the egg warm and get something to cushion the egg so its protected from damage and get something to keep the eggs steady.

Explanation:You have to build it yourself and get all supplies and figure out how to put it together. I wish you the best of luck and merry christmas

You might be interested in

g Let the charges start infinitely far away and infinitely far apart. They are placed at (6 cm, 0) and (0, 3 cm), respectively,

irina1246 [14]

Answer:

a) V =10¹¹*(1.5q₁ + 3q₂)

b) U = 1.34*10¹¹q₁q₂

Explanation:

Given

x₁ = 6 cm

y₁ = 0 cm

x₂ = 0 cm

y₂ = 3 cm

q₁ = unknown value in Coulomb

q₂ = unknown value in Coulomb

A) V₁ = Kq₁/r₁

where r₁ = √((6-0)²+(0-0)²)cm = 6 cm = 0.06 m

V₁ = 9*10⁹q₁/(0.06) = 1.5*10¹¹q₁

V₂ = Kq₂/r₂

where r₂ = √((0-0)²+(3-0)²)cm = 3 cm = 0.03 m

V₂ = 9*10⁹q₂/(0.03) = 3*10¹¹q₂

The electric potential due to the two charges at the origin is

V = ∑Vi = V₁ + V₂ = 1.5*10¹¹q₁ + 3*10¹¹q₂ = 10¹¹*(1.5q₁ + 3q₂)

B) The electric potential energy associated with the system, relative to their infinite initial positions, can be obtained as follows

U = Kq₁q₂/r₁₂

where

r₁₂ = √((0-6)²+(3-0)²)cm = √45 cm = 3√5 cm = (3√5/100) m

then

U = 9*10⁹q₁q₂/(3√5/100)

⇒ U = 1.34*10¹¹q₁q₂

5 0

3 years ago

A four-cylinder, four-stroke internal combustion engine has a bore of 3.7 in. and a stroke of 3.4 in. The clearance volume is 16

Bad White [126]

Answer:

the net work per cycle $\mathbf{W_{net} = 0.777593696}$ Btu per cycle

the power developed by the engine, W = 88.0144746 hp

Explanation:

the information given includes;

diameter of the four-cylinder bore = 3.7 in

length of the stroke = 3.4 in

The clearance volume = 16% = 0.16

The cylindrical volume $V_2 = 0.16 V_1$

the crankshaft N rotates at a speed of 2400 RPM.

At the beginning of the compression , temperature $T_1$ = 60 F = 519.67 R

and;

Otto cycle with a pressure = 14.5 lbf/in² = (14.5 × 144 ) lb/ft²

= 2088 lb/ft²

The maximum temperature in the cycle is 5200 R

From the given information; the change in volume is:

$V_1-V_2 = \dfrac{\pi}{4}D^2L$

$V_1-0.16V_1= \dfrac{\pi}{4}(3.7)^2(3.4)$

$V_1-0.16V_1= 36.55714291$

$0.84 V_1 =36.55714291$

$V_1 =\dfrac{36.55714291}{0.84 }$

$V_1 =43.52040823 \ in^3 \\ \\ V_1 = 43.52 \ in^3$

$V_1 = 0.02518 \ ft^3$

the mass in air ( lb) can be determined by using the formula:

$m = \dfrac{P_1V_1}{RT}$

where;

R = 53.3533 ft.lbf/lb.R°

$m = \dfrac{2088 \ lb/ft^2 \times 0.02518 \ ft^3}{53.3533 \ ft .lbf/lb.^0R \times 519 .67 ^0 R}$

m = 0.0018962 lb

From the tables of ideal gas properties at Temperature 519.67 R

$v_{r1} =158.58$

$u_1 = 88.62 Btu/lb$

At state of volume 2; the relative volume can be determined as:

$v_{r2} = v_{r1} \times \dfrac{V_2}{V_1}$

$v_{r2} = 158.58 \times 0.16$

$v_{r2} = 25.3728$

The specific energy $u_2$ at $v_{r2} = 25.3728$ is 184.7 Btu/lb

From the tables of ideal gas properties at maximum Temperature T = 5200 R

$v_{r3} = 0.1828$

$u_3 = 1098 \ Btu/lb$

To determine the relative volume at state 4; we have:

$v_{r4} = v_{r3} \times \dfrac{V_1}{V_2}$

$v_{r4} =0.1828 \times \dfrac{1}{0.16}$

$v_{r4} =1.1425$

The specific energy $u_4$ at $v_{r4} =1.1425$ is 591.84 Btu/lb

Now; the net work per cycle can now be calculated as by using the following formula:

$W_{net} = Heat \ supplied - Heat \ rejected$

$W_{net} = m(u_3-u_2)-m(u_4 - u_1)$

$W_{net} = m(u_3-u_2- u_4 + u_1)$

$W_{net} = m(1098-184.7- 591.84 + 88.62)$

$W_{net} = 0.0018962 \times (1098-184.7- 591.84 + 88.62)$

$W_{net} = 0.0018962 \times (410.08)$

$\mathbf{W_{net} = 0.777593696}$ Btu per cycle

the power developed by the engine, in horsepower. can be calculated as follows;

In the four-cylinder, four-stroke internal combustion engine; the power developed by the engine can be calculated by using the expression:

$W = 4 \times N' \times W_{net$

where ;

$N' = \dfrac{2400}{2}$

N' = 1200 cycles/min

N' = 1200 cycles/60 seconds

N' = 20 cycles/sec

W = 4 × 20 cycles/sec × 0.777593696

W = 62.20749568 Btu/s

W = 88.0144746 hp

8 0

3 years ago

If we have silicon at 300K with 10 microns of p-type doping of 4.48*10^18/cc and 10 microns of n-type doping at 1000 times less

liq [111]

Answer:

The resistance is 24.9 Ω

Explanation:

The resistivity is equal to:

$R=\frac{1}{N_{o}*u*V } =\frac{1}{4.48x10^{15}*1500*106x10^{-19} } =0.93ohm*cm$

The area is:

A = 60 * 60 = 3600 um² = 0.36x10⁻⁴cm²

$w=\sqrt{\frac{2E(V_{o}-V) }{p}(\frac{1}{N_{A} }+\frac{1}{N_{D} })$

If NA is greater, then, the term 1/NA can be neglected, thus the equation:

$w=\sqrt{\frac{2E(V_{o}-V) }{p}(\frac{1}{N_{D} })$

Where

V = 0.44 V

E = 11.68*8.85x10¹⁴ f/cm

$V_{o} =\frac{KT}{p} ln(\frac{N_{A}*N_{D}}{n_{i}^{2} } , if n_{i}=1.5x10^{10}cm^{-3} \\V_{o}=0.02585ln(\frac{4.48x10^{18}*4.48x10^{15} }{(1.5x10^{10})^{2} } )=0.83V$

$w=\sqrt{\frac{2*11.68*8.85x10^{-14}*(0.83-0.44) }{1.6x10^{-19}*4.48x10^{15} } } =3.35x10^{-5} cm=0.335um$

The length is:

L = 10 - 0.335 = 9.665 um

The resistance is:

$Re=\frac{pL}{A} =\frac{0.93*9.665x10^{-4} }{0.36x10^{-4} } =24.9ohm$

7 0

3 years ago

¿Qué aditivo se debe incorporar a la masa de hormigón para aumentar su resistencia frente a los ciclos alternados de hielo-deshi

tamaranim1 [39]

Answer:

Los aditivos que deben incorporarse a la masa de concreto para aumentar su resistencia a los ciclos alternos de congelación y descongelación son;

1. Agentes de arrastre de aire (AEA) o

2. Materiales poliméricos súper absorbentes

Explanation:

La resistencia alterna de los ciclos de congelación y descongelación en el concreto puede aumentarse mediante la adición de agentes de arrastre de aire.(AEA) que es un surfactante, crea burbujas de aire muy pequeñas en el concreto resultante para mejorar la durabilidad y resistencia del cemento al ciclo repetido de congelación y descongelación o materiales poliméricos súper absorbentes

Ejemplos de agentes de arrastre de aire son;

Sulfonatos alcalinos

Acidos de resinas sulfonadas

Sales de ácidos grasos

Ejemplos de materiales poliméricos superabsorbentes son;

SAP0.26CT

SAP0.39PT.

6 0

4 years ago

For a turning operation, you have selected a high-speed steel (HSS) tool and turning a hot rolled free machining steel. Your dep

Alisiya [41]

Answer:

MRR = 1.984

Explanation:

Given that

Depth of cut ,d=0.105 in

Diameter D= 1 in

Speed V= 105 sfpm

feed f= 0.015 ipr

Now the metal removal rate given as

MRR= 12 f V d

d= depth of cut

V= Speed

f=Feed

MRR= Metal removal rate

By putting the values

MRR= 12 f V d

MRR = 12 x 0.015 x 105 x 0.105

MRR = 1.984

Therefore answer is -

1.944

8 0

3 years ago