1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
allochka39001 [22]
3 years ago
5

Ammonia enters the expansion valve of a refrigeration system at a pressure of 10 bar and a temperature of 20oC and exits at 3.0

bar. The refrigerant undergoes a throttling process. Determine the temperature, in oC, and the quality of the refrigerant at the exit of the expansion valve. Step 1 Determine the temperature of the refrigerant at the exit, in oC.
Engineering
1 answer:
icang [17]3 years ago
3 0

Answer:

Ammonia enters the expansion valve of a refrigeration system at a pressure of 10 bar and a temperature of 20 o C and exits at 5.0 bar. The refrigerant undergoes a throttling process. Determine the temperature, in o C, and the quality of the refrigerant at the exit of the expansion valve.

Explanation:

You might be interested in
Why is concrete on its own not a good material to use
Inga [223]

Answer:

It has poor tensile strength despite having high compressive strength

Explanation:

Concrete exhibits high compressive strength when used. However, it has very low compressive strength. This is the reason why concrete is normally combined with steel to make a composite building material called reinforced concrete. The steel reinforces concrete hence increasing the tensile strength in RC buildings. The end composite is durable and fireproof. Generally, the main reason why concrete is not use on its own is due to its poor tensile strength.

7 0
3 years ago
REVIEW QUESTIONS
babunello [35]
Snap rings, and bearings can be used to keep a gear on a shaft, hope this helps!!
5 0
3 years ago
Someone has suggested that the air-standard Otto cycle is more accurate if the two polytropic processes are replaced with isentr
omeli [17]

Answer:

q_net,in = 585.8 KJ/kg

q_net,out = 304 KJ/kg

n = 0.481

Explanation:

Given:

- The compression ratio r = 8

- The pressure at state 1, P_1 = 95 KPa

- The minimum temperature at state 1, T_L = 15 C

- The maximum temperature T_H = 900 C

- Poly tropic index n = 1.3

Find:

a) Determine the heat transferred to and rejected from this cycle

b) cycle’s thermal efficiency

Solution:

- For process 1-2, heat is rejected to sink throughout. The Amount of heat rejected q_1,2, can be computed by performing a Energy balance as follows:

                                   W_out - Q_out = Δ u_1,2

- Assuming air to be an ideal gas, and the poly-tropic compression process is isentropic:

                         c_v*(T_2 - T_L) = R*(T_2 - T_L)/n-1 - q_1,2

- Using polytropic relation we will convert T_2 = T_L*r^(n-1):

                  c_v*(T_L*r^(n-1) - T_L) = R*(T_1*r^(n-1) - T_L)/n-1 - q_1,2

- Hence, we have:

                             q_1,2 = T_L *(r^(n-1) - 1)* ( (R/n-1) - c_v)

- Plug in the values:

                             q_1,2 = 288 *(8^(1.3-1) - 1)* ( (0.287/1.3-1) - 0.718)

                            q_1,2= 60 KJ/kg

- For process 2-3, heat is transferred into the system. The Amount of heat added q_2,3, can be computed by performing a Energy balance as follows:

                                          Q_in = Δ u_2,3

                                         q_2,3 = u_3 - u_2

                                         q_2,3 = c_v*(T_H - T_2)  

- Again, using polytropic relation we will convert T_2 = T_L*r^(n-1):

                                         q_2,3 = c_v*(T_H - T_L*r^(n-1) )    

                                         q_2,3 = 0.718*(1173-288*8(1.3-1) )

                                        q_2,3 = 456 KJ/kg

- For process 3-4, heat is transferred into the system. The Amount of heat added q_2,3, can be computed by performing a Energy balance as follows:

                                     q_3,4 - w_in = Δ u_3,4

- Assuming air to be an ideal gas, and the poly-tropic compression process is isentropic:

                           c_v*(T_4 - T_H) = - R*(T_4 - T_H)/1-n +  q_3,4

- Using polytropic relation we will convert T_4 = T_H*r^(1-n):

                  c_v*(T_H*r^(1-n) - T_H) = -R*(T_H*r^(1-n) - T_H)/n-1 + q_3,4

- Hence, we have:

                             q_3,4 = T_H *(r^(1-n) - 1)* ( (R/1-n) + c_v)

- Plug in the values:

                             q_3,4 = 1173 *(8^(1-1.3) - 1)* ( (0.287/1-1.3) - 0.718)

                            q_3,4= 129.8 KJ/kg

- For process 4-1, heat is lost from the system. The Amount of heat rejected q_4,1, can be computed by performing a Energy balance as follows:

                                          Q_out = Δ u_4,1

                                         q_4,1 = u_4 - u_1

                                         q_4,1 = c_v*(T_4 - T_L)  

- Again, using polytropic relation we will convert T_4 = T_H*r^(1-n):

                                         q_4,1 = c_v*(T_H*r^(1-n) - T_L )    

                                         q_4,1 = 0.718*(1173*8^(1-1.3) - 288 )

                                        q_4,1 = 244 KJ/kg

- The net gain in heat can be determined from process q_3,4 & q_2,3:

                                         q_net,in = q_3,4+q_2,3

                                         q_net,in = 129.8+456

                                         q_net,in = 585.8 KJ/kg

- The net loss of heat can be determined from process q_1,2 & q_4,1:

                                         q_net,out = q_4,1+q_1,2

                                         q_net,out = 244+60

                                         q_net,out = 304 KJ/kg

- The thermal Efficiency of a Otto Cycle can be calculated:

                                         n = 1 - q_net,out / q_net,in

                                         n = 1 - 304/585.8

                                         n = 0.481

6 0
3 years ago
The welding method that requires the operator to observe and only make corrections is
SVEN [57.7K]
Automatic manual semiautomatic
3 0
3 years ago
Read 2 more answers
Which statement about cathode ray tubes (CRTs) is true?
yuradex [85]

Answer:

CRTs consume less power than LCDs.

hope it helps (^^)

# Cary on learning

6 0
2 years ago
Other questions:
  • a. A crude oil pipe’s radius is reduced by 5%. What is the corresponding percentage change in the pressure drop per unit length?
    8·1 answer
  • These tadpoles are confined to a limited environment. What are they all competing for in that environment
    12·2 answers
  • Make a proposal to add a small pizza shop to a historical part of town. How could it be designed to “fit” into the area?
    7·2 answers
  • Three single-phase, 10 kVA, 2400/280 V, 60-Hz transformers are connected to form a three-phase, 2400/480 V transformer The equiv
    15·1 answer
  • A structural component in the form of a wide plate is to be fabricated from a steel alloy that has a plane-strain fracture tough
    10·1 answer
  • potential difference is the work done in moving a unit positive charge from one point to another in an electric field. State Tru
    12·1 answer
  • If noise levels are high enough that you have to raise
    7·1 answer
  • Refrigerant-134a enters the expansion valve of a refrigeration system at 120 psia as a saturated liquid and leaves at 20 psia. D
    15·1 answer
  • The following two DC motors are to be compared for certain application:
    13·1 answer
  • Incremental software development could be very effectively used for customers who do not have a clear idea about the systems nee
    5·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!