How can a sound of a different note be produced in a guitar without changing the length of wire?
2 answers:
You might be interested in
A) Acceleration:
B) The total displacement is 209.5 m north
C) The average velocity is 8.06 m/s north
Explanation:
A)
Acceleration is defined as:
where
v is the final velocity
u is the initial velocity
t is the time taken for the velocity to change from u to v
Here we have:
- In the first segment,
u = 8 m/s north
v = 11 m/s north
t = 4 s
So the acceleration is
(north)
- In the second segment, Stan drives at a constant velocity: so the final velocity is equal to the initial velocity,
u = v
Therefore, the acceleration is zero:
- In the third segment,
u = 11 m/s (north)
v = 0 (he comes to a stop)
t = 7 s
So the acceleration is
And the negative sign means the acceleration is south, opposite to the direction of motion.
B)
In a uniformly accelerated motion, the displacement can be calculated as:
where
u is the initial velocity
a is the acceleration
t is the time
- For the first segment, we have
So the displacement is
- For the second segment, we have
So the displacement is
- For the third segment, we have
So the displacement is
So the total displacement is:
s = 6 m + 165 m + 38.5 m = 209.5 m
In the north direction (positive direction)
C)
The average velocity is given by:
where
d is the total displacement
t is the total time
Here we have:
d = 209.5 m
t = 26 s
Therefore, the average velocity is
(north)
Learn more about accelerated motion:
#LearnwithBrainly
Answer:
The bulbs should be connected in parallel.
Explanation:
We want to find out a way to hook up 2 light bulbs and a battery so that when one bulb burns out or is disconnected the other bulbs stays lit.
We must connect the two bulbs in parallel so that even when one bulb is burns out, it will have no effect on the other bulb and the 2nd bulb will keep on working. The current flowing in each bulb will depend upon the resistance of each bulb and the voltage will be same across each bulb.
On the other hand, if we use a series circuit then if one bulb burns out then the there is no flow of current in the circuit and therefore, the second bulb will not be operational.
The current flowing through each bulb is given by
I = V/R
The voltage across each bulb is given by
V = IReq
Where I is the current and Req is the equivalent resistance of the two bulbs connected in parallel and is given by
Req = (R₁*R₂)/(R₁+R₂)
The connection diagram is attached where two bulbs are connected in parallel and are power with a battery.
Answer:
Speed is same as that before it entered glass.
Explanation:
Given:
A light ray enters and passes through the glass as shown in the diagram.
We have to analyze its speed.
Speed of light in air is and speed of light in glass is
Whenever a light ray enters a glass block or slab there is bending of light at the interface of the two media.
So speed of light will decrease in glass medium and again it passes to the air.
So
Speed of light in air will again increase or will be equivalent to the earlier speed when it was entering the glass block.
Finally
Speed is same as that before it entered glass as it in the same medium (air).
Answer:
Second order line appears at 43.33° Bragg angle.
Explanation:
When there is a scattering of x- rays from the crystal lattice and interference occurs, this is known as Bragg's law.
The Bragg's diffraction equation is :
.....(1)
Here n is order of constructive interference, λ is wavelength of x-ray beam, d is the inter spacing distance of lattice and θ is the Bragg's angle or scattering angle.
Given :
Wavelength, λ = 1.4 x 10⁻¹⁰ m
Bragg's angle, θ = 20°
Order of constructive interference, n =1
Substitute these value in equation (1).
d = 2.04 x 10⁻¹⁰ m
For second order constructive interference, let the Bragg's angle be θ₁.
Substitute 2 for n, 2.04 x 10⁻¹⁰ m for d and 1.4 x 10⁻¹⁰ m for λ in equation (1).
<em>θ₁ </em>= 43.33°