The uniform beam has a mass of 50 kg determine the reaction at the support

The input and output signals of a system is related by the following equation: fraction numerator d squared y over denominator d

Colt1911 [192]

Answer:

Explanation:

The given equation is :

$\frac{d^{2}y }{dx^{2} } + sin(3y) \frac{dy}{dt} + y = t\frac{df}{dt} + f$

5 0

3 years ago

Why is concrete on its own not a good material to use

Inga [223]

Answer:

It has poor tensile strength despite having high compressive strength

Explanation:

Concrete exhibits high compressive strength when used. However, it has very low compressive strength. This is the reason why concrete is normally combined with steel to make a composite building material called reinforced concrete. The steel reinforces concrete hence increasing the tensile strength in RC buildings. The end composite is durable and fireproof. Generally, the main reason why concrete is not use on its own is due to its poor tensile strength.

7 0

3 years ago

Steam enters an adiabatic turbine at 8 MPa and 500C with a mass flow rate of 3

Vinil7 [7]

Answer:

a)temperature=69.1C

b)3054Kw

Explanation:

Hello!

To solve this problem follow the steps below, the complete procedure is in the attached image

1. draw a complete outline of the problem

2. to find the temperature at the turbine exit use termodinamic tables to find the saturation temperature at 30kPa

note=Through laboratory tests, thermodynamic tables were developed, these allow to know all the thermodynamic properties of a substance (entropy, enthalpy, pressure, specific volume, internal energy etc ..)

through prior knowledge of two other properties such as pressure and temperature.

3. Using thermodynamic tables find the enthalpy and entropy at the turbine inlet, then find the ideal enthalpy using the entropy of state 1 and the outlet pressure = 30kPa

4. The efficiency of the turbine is defined as the ratio between the real power and the ideal power, with this we find the real enthalpy.

Note: Remember that for a turbine with a single input and output, the power is calculated as the product of the mass flow and the difference in enthalpies.

5. Find the real power of the turbine

3 0

3 years ago

A furnace wall composed of 200 mm, of fire brick. 120 mm common brick 50mm 80% magnesia and 3mm of steel plate on the outside. I

Liula [17]

Answer:

fire brick / common brick : 1218 °C
common brick / magnesia : 1019 °C
magnesia / steel : 90.06 °C
heat loss: 4644 kJ/m^2/h

Explanation:

The thermal resistance (R) of a layer of thickness d given in °C·m²·h/kJ is ...

R = d/k

so the thermal resistances of the layers of furnace wall are ...

R₁ = 0.200/4 = 0.05 °C·m²·h/kJ

R₂ = 0.120 2.8 = 3/70 °C·m²·h/kJ

R₃ = 0.05/0.25 = 0.2 °C·m²·h/kJ

R₄ = 0.003/240 = 1.25×10⁻⁵ °C·m²·h/kJ

So, the total thermal resistance is ...

R₁ +R₂ +R₃ +R₄ = R ≈ 0.29286 °C·m²·h/kJ

__

The rate of heat loss is ΔT/R = (1450 -90)/0.29286 = 4643.70 kJ/(m²·h)

__

The temperature drops across the various layers will be found by multiplying this heat rate by the thermal resistance for the layer:

fire brick: (4543.79 kJ/(m²·h))(0.05 °C·m²·h/kJ) = 232 °C

so, the fire brick interface temperature at the common brick is ...

1450 -232 = 1218 °C

For the next layers, the interface temperatures are ...

common brick to magnesia = 1218 °C - (3/70)(4643.7) = 1019 °C

magnesia to steel = 1019 °C -0.2(4643.7) = 90.06 °C

_____

<em>Comment on temperatures</em>

Most temperatures are rounded to the nearest degree. We wanted to show the small temperature drop across the steel plate, so we showed the inside boundary temperature to enough digits to give the idea of the magnitude of that.

5 0

3 years ago

Shows a closed tank holding air and oil to which is connected a U-tube mercury manometer and a pressure gage. Determine the read

damaskus [11]

Answer:

$P_2-P_1=27209h$

Explanation:

For pressure gage we can determine this by saying:

The closed tank with oil and air has a pressure of P₁ and the pressure of oil at a certain height in the U-tube on mercury is p₁gh₁. The pressure of mercury on the air in pressure gauge is p₂gh₂. The pressure of the gage is P₂.

$P_1+p_1gh_1=p_2_gh_2+P_2$

We want to work out P₁-P₂: Heights aren't given so we can solve it in terms of height: assuming h₁=h₂=h

$P_1-P_2=p_1gh_1-p_2gh_2=(55)\cdot{32.2}h-845\cdot{32.2}h$

$P_2-P_1=27209h$

3 0

4 years ago

The uniform beam has a mass of 50 kg determine the reaction at the support​

The uniform beam has a mass of 50 kg determine the reaction at the support