All categories

2 years ago

I will give Brainliest, please help. :)

Engineering

2 answers:

ziro4ka [17]2 years ago

7 0

Answer:

The ratio of water to flour needed to make tortillas, which is 3 : 4

Explanation:

100 w = 75 f

w/f = 75/100 = 3/4

Bezzdna [24]2 years ago

4 0

The ratio of water to flour (4:3)

You might be interested in

A 10-mm steel drill rod was heat-treated and ground. The measured hardness was found to be 290 Brinell. Estimate the endurance s

grandymaker [24]

Answer:

the endurance strength $S_e$ = 421.24 MPa

Explanation:

From the given information; The objective is to estimate the endurance strength, Se, in MPa .

To do that; let's for see the expression that shows the relationship between the ultimate tensile strength and Brinell hardness number .

It is expressed as:

$200 \leq H_B \leq 450$

$S_{ut} = 3.41 H_B$

where;

$H_B$ = Brinell hardness number

$S_{ut}$ = Ultimate tensile strength

From ;

$S_{ut} = 3.41 H_B$ ; replace 290 for $H_B$ ; we have

$S_{ut} = 3.41 (290)$

$S_{ut} =$ 988.9 MPa

We can see that the derived value for the ultimate tensile strength when the Brinell harness number = 290 is less than 1400 MPa ( i.e it is 988.9 MPa)

So; we can say

$S_{ut} < 1400$

The Endurance limit can be represented by the formula:

$S_e ' = 0.5 S_{ut}$

$S_e ' = 0.5 (988.9)$

$S_e '$ = 494.45 MPa

Using Table 6.2 for parameter for Marin Surface modification factor. The value for a and b are derived; which are :

a = 1.58

b = -0.085

The value of the surface factor can be calculate by using the equation

$k_a = aS^b_{ut}$

$K_a = 1.58 (988.9)^{-0.085$

$K_a = 0.8792$

The formula that is used to determine the value of $k_b$ for the rotating shaft of size factor d = 10 mm is as follows:

$k_b = 1.24d^{-0.107}$

$k_b = 1.24(10)^{-0.107}$

$k_b = 0.969$

Finally; the the endurance strength, Se, in MPa if the rod is used in rotating bending is determined by using the expression;

$S_e =k_ak_b S' _e$

$S_e$ = 0.8792×0.969×494.45

$S_e$ = 421.24 MPa

Thus; the endurance strength $S_e$ = 421.24 MPa

8 0

3 years ago

Consider the circuit below where R1 = R4 = 5 Ohms, R2 = R3 = 10 Ohms, Vs1 = 9V, and Vs2 = 6V. Use superposition to solve for the

VladimirAG [237]

Answer:

The value of v2 in each case is:

A) V2=3v for only Vs1

B) V2=2v for only Vs2

C) V2=5v for both Vs1 and Vs2

Explanation:

In the attached graphic we draw the currents in the circuit. If we consider only one of the batteries, we can consider the other shorted.

Also, what the problem asks is the value V2 in each case, where:

$V_2=I_2R_2=V_{ab}$

If we use superposition, we passivate a battery and consider the circuit affected only by the other battery.

In the first case we can use an equivalent resistance between R2 and R3:

$V_{ab}'=I_1'R_{2||3}=I_1'\cdot(\frac{1}{R_2}+\frac{1}{R_3})^{-1}$

And

$V_{S1}-I_1'R_1-I_1'R_4-I_1'R_{2||3}=0 \rightarrow I_1'=0.6A$

$V_{ab}'=I_1'R_{2||3}=3V=V_{2}'$

In the second case we can use an equivalent resistance between R2 and (R1+R4):

$V_{ab}''=I_3'R_{2||1-4}=I_3'\cdot(\frac{1}{R_2}+\frac{1}{R_1+R_4})^{-1}$

And

$V_{S2}-I_3'R_3-I_3'R_{2||1-4}=0 \rightarrow I_3'=0.4A$

$V_{ab}''=I_3'R_{2||1-4}=2V$

If we consider both batteries:

$V_2=I_2R_2=V_{ab}=V_{ab}'+V_{ab}''=5V$

7 0

3 years ago

Drivers killed in speed related accidents usually have a history of_______

bazaltina [42]

I would go with C but i am not 100 percent on that

3 0

3 years ago

Read 2 more answers

A glass tube is inserted into a flowing stream of water with one opening directed upstream and the other end vertical. If the wa

Furkat [3]

Answer:

$h=0.46m$

Explanation:

From the question we are told that:

Velocity of water $V=3m/s$

Height=?

Generally, the equation for Water Velocity is mathematically given by

$V=\sqrt{2gh}$

Therefore Height h is given as

$h=\frac{v}{2g}$

$h=\frac{3^2}{2*9.81}$

$h=0.46m$

5 0

3 years ago

technician a says that the higher the gear selected the more torque is available. technician b says that a transaxle contains ge

umka21 [38]

Technician A is correct. Technician B is wrong because a gear's transmission is used to increase or decrease torque.

The relation torque is relying on multiplying the circumferential detail with the resource of the usage of the radius; massive gears experience a greater amount of torque, at the same time as smaller gears experience a great deal much less torque. Similarly, the torque ratio is equal to the ratio of the gears' radii. A gear's transmission torque modifications as it will boom or decreases speed. Commonly, with the resource of the usage of lowering the speed, a small torque on the doorway issue is transferred as a massive torque at the output issue. The calculation of torque is quantified with the resource of the usage of an extensive form of teeth.

Learn more about the torque at brainly.com/question/28220969

#SPJ4

3 0

1 year ago