All categories

2 years ago

Explain Why programs when are developed using evolutionary development are likely to be difficult to maintain

Engineering

1 answer:

Lerok [7]2 years ago

5 0

Answer:

When a system is produced using the evolutionary development model, features tend to be added without regard to an overriding design. With each modification, the software becomes increasingly disorganized. System maintenance hampered by these problems, as it is harder identifying the source of bugs in poorly designed systems. Also, keeping the documentation up to date over successive "evolution" is uncommon. Poor documentation also makes maintenance more difficult.

Explanation:

・It leads to implementing and then repairing way of building systems.

・Practically, this methodology may increase the complexity of the system as scope of the system may expand beyond original plans.

・Incomplete application may cause application not to be used as the full system was designed.

・Their results have incomplete or inadequate problem analysis.

You might be interested in

The following laboratory test results for Atterberg limits and sieve-analysis were obtained for an inorganic soil. [6 points] Si

alexira [117]

Answer: hello the complete question is attached below

answer:

A) Group symbol = SW

B) Group name = well graded sand , fine to coarse sand

C) It is not a clean sand given that ≤ 50% particles are retained on No 200

Explanation:

A) Classifying the soil according to USCS system

( using 2nd image attached below )

description of sand :

The soil is a coarse sand since ≤ 50% particles are retained on No 200 sieve, also

The soil is a sand given that more than 50% particles passed from No 4 sieve

The soil can be a clean sand given that fines ≤ 12%

The soil can be said to be a well graded sand because the percentage of particles passing through decreases gradually over time

Group symbol as per the 2nd image attached below = SW

B) Group name = well graded sand , fine to coarse sand

C) It is not a clean sand given that ≤ 50% particles are retained on No 200

5 0

3 years ago

W10L1-Show It: Pythagorean Theorem Calculate the total material in the picture. 4 3

Fantom [35]

Answer:

Explanation: I really dont even know, I just used up all my tries on it and got it wrong on every other thing i chose. So it's 35 i believe cause its the only answer i didnt choose.

7 0

3 years ago

A small pad subjected to a shearing force is deformed at the top of the pad 0.08 in. The height of the pad is 1.38 in. What is t

Aleksandr-060686 [28]

Answer:

The shear strain is 0.05797 rad.

Explanation:

Shear strain is the ratio of change in dimension along the shearing load direction to the height of the plate under application of shear load. Width of the plate remains same. Length of the plate slides under shear load.

Step1

Given:

Height of the pad is 1.38 in.

Deformation at the top of the pad is 0.08 in.

Calculation:

Step2

Shear strain is calculated as follows:

$tan\phi=\frac{\bigtriangleup l}{h}$

$tan\phi=\frac{0.08}{1.38}$

$tan\phi= 0.05797$

For small angle of $\phi$ , $tan\phi$ can take as $\phi$ .

$\phi = 0.05797 rad.$

Thus, the shear strain is 0.05797 rad.

7 0

3 years ago

It is appropriate to use the following yield or failure criterion for ductile materials (a) Maximum shear stress or Tresca crite

Nataly [62]

Answer:

(b)Distortion energy theory.

Explanation:

The best suitable theory for ductile material:

(1)Maximum shear stress theory (Guest and Tresca theory)

It theory state that applied maximum shear stress should be less or equal to its maximum shear strength.

(2)Maximum distortion energy theory(Von Mises henkey's theory)

It states that maximum shear train energy per unit volume at any point is equal to strain energy per unit volume under the state of uni axial stress condition.

But from these two Best theories ,suitable theory is distortion energy theory ,because it gives best suitable result for ductile material.

6 0

3 years ago

A piece of aluminum wire is 500 ft long and has a diameter of 0.03 inches. What is the resistance of the piece of wire?

dexar [7]

Answer:

8.85 Ω

Explanation:

Resistance of a wire is:

R = ρL/A

where ρ is resistivity of the material,

L is the length of the wire,

and A is the cross sectional area.

For a round wire, A = πr² = ¼πd².

For aluminum, ρ is 2.65×10⁻⁸ Ωm, or 8.69×10⁻⁸ Ωft.

Given L = 500 ft and d = 0.03 in = 0.0025 ft:

R = (8.69×10⁻⁸ Ωft) (500 ft) / (¼π (0.0025 ft)²)

R = 8.85 Ω

5 0

4 years ago