Answer:
Explanation:
The deatailed diagram of VCRS is given below such
1-2=Isentropic compression in which temperature increases at constant entropy
2-3=Isobaric heat rejection i.e. heat rejected at constant pressure(condensation)
3-4=Irreversible expansion or throttling in which enthalpy remains constant
4-1=Isobaric heat addition(Evaporation)
Answer:
Minimum Allowable diameter for each of the 5 bolts = 0.0394 m = 3.94 cm
Explanation:
Maximum Working Stress = Ultimate Shear Stress/factor of safety
Maximum Working Stress = 280 MPa/3.8 = 73.68 MPa
Working Stress = Applied load/Minimum allowable Area = L/A
Minimum Allowable Area = Applied Load/Maximum Working Stress
A = 450000/73680000 = 0.00611 m²
This area is supplied by 5 bolts, so each bolt supplies A/5 = 0.0061/5 = 0.00122 m²
Cross sectional Area of bolts = πD²/4
0.00122 = πD²/4
D² = 4 × 0.00122/π = 0.00155
D = √0.00155 = 0.0394 m = 3.94 cm
Each of the five bolt can have a minimum diameter of 3.94 cm
Hope this Helps!!!
Answer:
Option C (IaaS) will be the correct answer.
Explanation:
- IaaS is essentially a cloud strategy that enables an individual or company to rent resources including such servers, networking devices including data or storage management. IaaS is a digital storage facility.
- PaaS can not provide root privileges as even the hosting company would control the network. Here, SaaS as well as DBaaS aren't important.
That will be the right answer to the question.
Answer:
R = 31.9 x 10^(6) At/Wb
So option A is correct
Explanation:
Reluctance is obtained by dividing the length of the magnetic path L by the permeability times the cross-sectional area A
Thus; R = L/μA,
Now from the question,
L = 4m
r_1 = 1.75cm = 0.0175m
r_2 = 2.2cm = 0.022m
So Area will be A_2 - A_1
Thus = π(r_2)² - π(r_1)²
A = π(0.0225)² - π(0.0175)²
A = π[0.0002]
A = 6.28 x 10^(-4) m²
We are given that;
L = 4m
μ_steel = 2 x 10^(-4) Wb/At - m
Thus, reluctance is calculated as;
R = 4/(2 x 10^(-4) x 6.28x 10^(-4))
R = 0.319 x 10^(8) At/Wb
R = 31.9 x 10^(6) At/Wb
Answer:
A) while (num >= 0)
Explanation:
To understand why we need to focus on the module and division operation inside the loop. num % 10 divide the number by ten and take its remainder to then add this remainder to sum, the important here is that we are adding up the number in reverse order and wee need to repeat this process until we get the first number (1%10 = 1), therefore, num need to be one to compute the last operation.
A) this is the correct option because num = 1 > 0 and the last operation will be performed, and after the last operation, num = 1 will be divided by 10 resulting in 0 and 0 is not greater than 0, therefore, the cycle end and the result will be printed.
B) This can not be the option because this way the program will never ends -> 0%10 = 0 and num = 0/10 = 0
C) This can not be the option because num = 1 > 1 will produce an early end of the loop printing an incomplete result
D) The same problem than C
E) There is a point, before the operations finish, where sum > num, this will produce an early end of the loop, printing an incomplete result
