1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
lakkis [162]
3 years ago
6

A certain full-wave rectifier has a peak output voltage of 30 V. A 50 mF capacitor-input filter is connected to the rectifier. C

alculate the peak-to-peak ripple and the dc output voltage devel-oped across a 600 V load resistance.
Engineering
1 answer:
Minchanka [31]3 years ago
5 0

Answer:

Peak to peak Ripple voltage 8.33mV

DC output voltage =19.11 V

Explanation:

Peak voltage( Vp)= 30v

Load resistance =600 ohms

Capacitor filter = 50mF

Frequency of supply = 120Hz

The peak to peak Ripple is not only dependent on the capacitor value but also on the frequency and load current.

To calculate the,

Peak to peak ripple = I (load)/f×c

I (load) = loadd current = 30/600 = 0.05 A

Peak to peak ripple = 0.05/6

= 8.33mV

The average Dc output voltage for a full wave rectifier is double that of a half wave rectifier.

The DC output voltage is equal to 0.637Vp assuming no losses.

Vdc= 0.637 × 30

Vdc =19.11V

You might be interested in
Select the correct answer. Sean is a recent engineering graduate who has joined a new company. Read the profiles of his colleagu
PSYCHO15rus [73]

Answer:

giving advertising to the governor with the state

4 0
3 years ago
A(n) ___ is an electric device that uses electromagnetism to change (step up or step down) AC voltage from one level to another.
Pie

Answer:

A transformer is an electric device that uses electromagnetism to change voltage from one level to another or to isolate one voltage from another.

7 0
3 years ago
You wish to design a cantilever beam with a square cross section and length L that can support an end load of F without yielding
koban [17]

Answer:

with a square cross section and length L that can support an end load of F without yielding. You also wish to minimize the amount the beam deflects under load. What is the free variable(s) (other than the material) for this design problem?

a. End load, F.

b. Length, L.

c. Beam thickness, b

d. Deflection, δ

e. Answers b and c.

f. All of the above.

8 0
3 years ago
What the different methods to turn on thyrister and how can a thyrister turned off​
myrzilka [38]

Answer:

forward voltage triggering

temperature triggering

dv/dt triggering

light triggering

gate triggering

Then turning off;

Turn off is accomplished by a "negative voltage" pulse between the gate and cathode terminals

Explanation:

hope it helps

8 0
3 years ago
Your family has asked you to estimate the operating costs of your clothes dryer for the year. The clothes dryer in your home has
trasher [3.6K]

Answer:

The costs to run the dryer for one year are $ 9.03.

Explanation:

Given that the clothes dryer in my home has a power rating of 2250 Watts, and to dry one typical load of clothes the dryer will run for approximately 45 minutes, and in Ontario, the cost of electricity is $ 0.11 / kWh, to calculate the costs to run the dryer for one year the following calculation must be performed:

1 watt = 0.001 kilowatt

2250/45 = 50 watts per minute

45 x 365 = 16,425 / 60 = 273.75 hours of consumption

50 x 60 = 300 watt = 0.3 kw / h

0.3 x 273.75 = 82.125

82.125 x 0.11 = 9.03

Therefore, the costs to run the dryer for one year are $ 9.03.

8 0
3 years ago
Other questions:
  • What are the main causes of injuries when using forklifts?
    12·2 answers
  • The dramatic growth in the number of power data centers, cell towers, base stations, recharge mobiles, and so on is damaging the
    8·1 answer
  • Technician A says that a seal can be pried out of a bore using a sharp chisel. Technician B says that smaller metal-backed seals
    7·2 answers
  • A 2-kg ball B is traveling horizontally at 10 m/s when it strikes 2-kg ball A. Ball A is initially at rest and is attached to a
    9·1 answer
  • The intercept of the CML is the origin while the intercept of the SML is RF CML consists of efficient portfolios, while the SML
    12·1 answer
  • In the High Low Logic Index low levels are bearish and high levels are bullish, generally True False
    13·1 answer
  • What car has autopilot?
    14·2 answers
  • Construction lines are thick lines true false
    11·2 answers
  • please answer correctly if it is not correct, report it to them thank you for answering correctly.god bless you​
    8·2 answers
  • What is the definition of gross axle weight rating?.
    5·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!