1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
Soloha48 [4]
3 years ago
7

How many answer do you need to have a conversation ?

Engineering
1 answer:
NeX [460]3 years ago
5 0

i am kinda new, perhaps means the thread and discussion when someone answers.

You might be interested in
If a ball is dropped from a height​ (H) its velocity will increase until it hits the ground​ (assuming that aerodynamic drag due
enot [183]

Answer

Explanation:

so the velocity is 39 feet per sec so the impact is 720 cm from the ground

take 720 * 39 sq

4 0
4 years ago
Do you think the plan for the bridge in South America is appropriate based on its location? Why or why not? Your answer should i
pashok25 [27]
I don’t think it is because it is to big and heavy for the ground to support and the bridge will sink in a short amount of time. they should think about using better materials on the bridge. they should also locate it in a better area.
6 0
3 years ago
Read 2 more answers
Water is pumped from one large reservoir to another at a higher elevation. If the flow rate is 2.5 ft3 /s and the pump delivers
4vir4ik [10]

Answer:

2132hp  ed enregia

e

Explanation:

dawdsawdsawdsawdsawdsawdsawdaas

6 0
4 years ago
What tools do you need to change a flat tire
Lyrx [107]

Answer:

  • Spare tire (if you’re dealing with a flat and not just rotating tires or accessing the brakes)
  • Carjack
  • Lug wrench
  • Wheel wedges
  • Work gloves
  • Tire repair kit (if you’re attempting to fix your flat tire)
  • Flare/reflective triangles (if you’re changing the tire on the side of the road or in a parking lot)
6 0
4 years ago
Read 2 more answers
1) Find the time in seconds to reach full charge in an RL circuit with L = 5 H and R = 100 ohms
pav-90 [236]

The time constant to reach full charge in an RL circuit is 0.05 ms.

Explanation:

To find the time constant,

The time constant for an RL circuit is defined by τ = L/R.

The given data is

L= 5 H

R= 100 ohms

by using the formula,

τ = L/R

  = 5/100

  = 0.05 ms

τ = 0.05 ms

Thus, the time constant to reach full charge in an RL circuit is 0.05 ms.

8 0
3 years ago
Other questions:
  • The minimum size for overhead service conductors shall not be smaller than ____ AWG copper. A. 4 B. 6 C. 8 D. 10
    13·1 answer
  • A 2-kg ball B is traveling horizontally at 10 m/s when it strikes 2-kg ball A. Ball A is initially at rest and is attached to a
    9·1 answer
  • Carbon nanotubes can be a considered toxic agent due to: (a)- Its ability to produce toxic gases (b)Its ability to penetrate ski
    8·1 answer
  • A single-threaded power screw is 35 mm in diameter with a pitch of 5 mm. A vertical load on the screw reaches a maximum of 5 kN.
    13·1 answer
  • Need the answer ASAP
    6·1 answer
  • A mason requires 12 mason-hours per 100 ft2 for the bottom 4 ft of wall, and a hod carrier requires 14.5 helper hours to mix the
    12·1 answer
  • A ball of 0.900 kg slides horizontally over a frictionless surface and bumps into a heavy stone at a speed of 20.0 m / s. The ba
    12·1 answer
  • How to draw the output voltage waveform rectifier
    8·1 answer
  • Giving away points hope they help with your questions
    14·1 answer
  • What are the advantages of using a network?
    10·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!