All categories

4 years ago

Give two advantages of a four-high rolling mill opposed to a two-high rolling mill for the same output diameter.

Engineering

1 answer:

uysha [10]4 years ago

7 0

Answer:

Four- high rolling mill  Two-high rolling mill

1.Small roll radius.That is why required 1.High roll radius.That is required low power. . why required high power.

2. Low roll separating force. 2.High roll separating

force

You might be interested in

In a creep test, increasing the temperature will (choose the best answer) A. increase the instantaneous initial deformation B. i

Hitman42 [59]

Answer:

All of the above

Explanation:

firstly, a creep can be explained as the gradual deformation of a material over a time period. This occurs at a fixed load with the temperature the same or more than the recrystallization temperature.

Once the material gets loaded, the instantaneous creep would start off and it is close to electric strain. in the primary creep area, the rate of the strain falls as the material hardens. in the secondary area, a balance between the hardening and recrystallization occurs. The material would get to be fractured hen recrstallization happens. As temperature is raised the recrystallization gets to be more.

8 0

3 years ago

The angle of twist can be computed using the material’s shear modulus if and only if: (a)- The shear stress is still in the elas

ollegr [7]

Answer:

The angle of twist can be computed using the material’s shear modulus if and only if the shear stress is still in the elastic region

Explanation:

The shear modulus (G) is the ratio of shear stress to shear strain. Like the modulus of elasticity, the shear modulus is governed by Hooke’s Law: the relationship between shear stress and shear strain is proportional up to the proportional limit of the material. The angle of twist can be computed using the material’s shear modulus if and only if the shear stress is still in the elastic region.

3 0

4 years ago

A biotechnology company produced 225 doses of somatropin, including 11 which were defective. Quality control test 15 samples at

Radda [10]

Answer:

0.59

Explanation:

The batch is rejected if any of the random samples are found defective, or, what is the same, it will be accepted only if all 15 samples are good.

The probability that none be defective is the same probability that all the samples are good. Thus, start to calculate the probability that the batch is accepted.

The probability that the first sample is good is 214 /225, because there are 225 - 11 = 214 good samples in 225 doses.

The probability that the second samples is good too is 213/224, because there is 1 less good sample, in the 224 remaining samples.

By the same process, you conclude that the consecutive probabilities of selecting a good sample are: 212/223, 211/222, 210/221, . . . up to 199/211.

The joint probability of all the samples are good is the product of each probability:

$\frac{214}{225}\cdot\frac{213}{224}\cdot\frac{212}{223}\cdot\frac{211}{222}\cdot\frac{210}{221}\cdot\frac{209}{220}\cdot\frac{208}{219}\cdot\frac{207}{218}\cdot\frac{206}{217}\cdot\frac{205}{216}\cdot\frac{204}{215}\cdot\frac{203}{214}\cdot\frac{202}{213}\cdot\frac{201}{212}\cdot\frac{200}{211}\cdot\frac{199}{210}$

The result is: 0.41278 ≈ 0.41

The conclusion is that the probability that all the samples are good and the batch is accepted is 0.41.

Therefore, the probability that the batch is rejected is 1 - 0.41 = 0.59.

4 0

4 years ago

Seawater containing 3.50 wt% salt passes through a series of 11 evaporators. Roughly equal quantities of water are vaporized in

statuscvo [17]

Answer: the mass flow rate of concentrated brine out of the process is 46,666.669 kg/hr

Explanation:

F, W and B are the fresh feed, brine and total water obtained

w = 2 x 10^4 L/h

we know that

F = W + B

we substitute

F = 2 x 10^4 + B

F = 20000 + B .................EQUA 1

solute

0.035F = 0.05B

B = 0.035F/0.05

B = 0.7F

now we substitute value of B in equation 1

F = 20000 + 0.7F

0.3F = 20000

F = 20000/0.3

F = 66666.67 kg/hr

B = 0.7F

B = 0.7 * F

B = 0.7 * 66666.67

B = 46,666.669 kg/hr

the mass flow rate of concentrated brine out of the process is 46,666.669 kg/hr

8 0

4 years ago

A person walks into a refrigerated warehouse with head uncovered. Model the head as a 25- cm diameter sphere at 35°C with a surf

galina1969 [7]

Answer:

Hello some parts of your question is missing below is the missing part

Convection coefficient = 11 w/m^2. °c

answer : 44.83 watts

Explanation:

Given data :

surface emissivity ( ε )= 0.95

head ( sphere) diameter( D ) = 0.25 m

Temperature of sphere( T ) = 35° C

Temperature of surrounding ( T∞ ) = 25°C

Temperature of surrounding surface ( Ts ) = 15°C

б = ( 5.67 * 10^-8 )

Determine the total rate of heat loss

First we calculate the surface area of the sphere

As = $\pi D^{2}$

= $\pi * 0.25^2$ = 0.2 m^2

next we calculate heat loss due to radiation

Qrad = ε * б * As( $T^{4} - T^{4} _{s}$ ) ---- ( 1 )

where ;

ε = 0.95

б = ( 5.67 * 10^-8 )

As = 0.2 m^2

T = 35 + 273 = 308 k

Ts = 15 + 273 = 288 k

input values into equation 1

Qrad = 0.95 * ( 5.67 * 10^-8 ) * 0.2 ( (308)^4 - ( 288)^4 )

= 22.83 watts

Qrad ( heat loss due to radiation ) = 22.83 watts

calculate the heat loss due to convection

Qconv = h* As ( ΔT )

= 11*0.2 ( 35 -25 ) = 22 watts

Hence total rate of heat loss

= 22 + 22.83

= 44.83 watts

5 0

3 years ago