1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
sveta [45]
3 years ago
12

Derive the probability that a receptor is occupied by a ligand using a model that treats the L ligands in solution as distinguis

hable particles. Show that the expression is the same as obtained in the text (Equation 6.19), where the ligands were treated as indistinguishable.
Engineering
1 answer:
love history [14]3 years ago
7 0

that is the same thing as you are not going through this week or something

You might be interested in
The energy flux associated with solar radiation incident on the outer surface of the earth’s atmosphere has been accurately meas
Degger [83]

Answer:

A) 3.868x10^26 W

B) 8176.678 K

C) 3.544x10^-7 m

D) 393.187 K

Explanation:

Detailed explanation and calculation is shown in the image below.

8 0
3 years ago
WHAT IS THE EFFECT OF ICE ACCRETION ON THE LONGITUDINAL STABILITY OF AN AIRCRAFT?
soldier1979 [14.2K]

Answer:

The major effects of ice accretion on the aircraft is that it disturbs the flow of air and effects the aircraft's performance.

Explanation:

The ice accretion effects the longitudinal stability of an aircraft as:

1. The accumulation of ice on the tail of an aircraft results in the reduction the longitudinal stability and  the elevator's efficacy.

2. When the flap is deflected at 10^{\circ} with no power there is an increase in the longitudinal velocity.  

3. When the angle of attack is higher close to the stall where separation occurs in the early stages of flow, the effect of ice accretion are of importance.  

4. When the situation involves no flap  at reduced power setting results in the decrease in aircraft's longitudinal stability an increase in change in coefficient of pitching moment  with attack angle.

5 0
4 years ago
A pressure gage and a manometer are connected to a compressed air tank to measure its pressure. If the reading on the pressure g
mixer [17]

Answer:

h=1.122652m

Explanation:

Assuming density of air = 1.2kg/m³

the differential pressure is given by:

h^{i} =h(\frac{density of manometer}{density of flowing air}-1)\\h^{i} =h(\frac{1000}{1.2}-1)\\ h^{i}=832.33h...(1)\\\\but\\ h^{i} =\frac{change in pressure}{air density*g} \\\\h^{i} =\frac{11*10^3}{1.2*9.81}\\\\h^{i}= 934.42...(2)\\\\equating, \\\\934.42=832.33h\\\\h=1.122652m

7 0
4 years ago
A 0.4-W cylindrical electronic component with diameter 0.3 cm and length 1.8 cm and mounted on a circuit board is cooled by air
Katyanochek1 [597]

Answer:

The surface temperature of the component 54.6 degrees celsius.

Explanation:

Please see attachment.

7 0
3 years ago
The graph to the right shows the amount of acres burned by wildfires in the 11 western states of the United States between 1916
qaws [65]

Answer:

it goes low to high off and on

Explanation:

because i wrote it

4 0
3 years ago
Other questions:
  • Two plates are separated by a 1/4 in space. The lower plate is stationary; the upper plate moves at 10 ft/s. Oil (viscosity of 2
    10·1 answer
  • Explain the benefits of reading A vocabulary section at the beginning of a text
    10·2 answers
  • A balanced three phase load is supplied over a three-phase , 60 hz, transmission line with each line have a series impedance of
    10·1 answer
  • Consider that a system has two entities, Students, Instructors and Course. The Student has the following properties: student nam
    12·1 answer
  • In a tension test of steel, the ultimate load was 13,100 lb and the elongation was 0.52 in. The original diameter of the specime
    9·1 answer
  • In a CNC machining operation, the has to be moved from point (5, 4) to point(7, 2)along a circular path with center at (7,2). Be
    5·1 answer
  • A structural element for a new bridge is designed for a constant load of 1000 psi. Its mean resistance is 1200 psi and the proba
    7·1 answer
  • Most goals
    12·1 answer
  • Select the correct answer. which process involves creating a product by heating metals and changing their shape through the appl
    13·1 answer
  • 1. A car engine transfers 3000J in 20 seconds. What is the power generated by the engine?
    5·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!