Calculate the percent of iron in iron (III) hydroxide

What kind of oxide is formed when a piece of sodium is dropped in the water

aleksley [76]

Answer:

Sodium oxide is the product

Explanation:

4Na+O2->2Na2O

7 0

3 years ago

(A) H2SeO4(aq) + 2 Cl-(aq) + 2 H+(aq) → H2SeO3(aq) + Cl2(g) + H2O(l) (B) S8(s) + 8 O2(g) → 8 SO2(g) (C) 3 Br2(aq) + 6 OH-(aq) →

AVprozaik [17]

Answer:

C)

Explanation:

Oxidation occurs when the Nox number increases and a reduction occurs when the Nox number decreases. So, let's verify in which reaction the same reactant has elements that both occur after the reaction.

A) H₂SeO₄: H = +1, O = -2 (fixed)

Se: x +2*1 + 4*(-2) = 0

x + 2 - 8= 0

x = +6

Cl⁻: -1 (ions have Nox equal to its charge)

H⁺: +1

H₂SeO₃: H = + 1, O = -2

Se: x +2*1 + 3*(-2) = 0

x + 2 -6 = 0

x = + 4 (Se reduces)

Cl₂: Cl = 0 (simple molecule, so Cl oxides)

H₂O: H = +1, O = -2

B) S₈: S = 0

O₂: O = 0

SO₂: O = -2, S: x + 2*(-2) = 0 -> x = +4 (S oxides and O reduces)

C) Br₂: Br = 0

OH⁻ : O = -2, H = +1

Br⁻ = -1 (Br reduces)

BrO₃⁻: O = -2, Br: x +3x(-2) = -1 -> x = +5 (Br oxides)

H₂O: H = +1, O = -2

D) Ca²⁺: Ca = +2

SO₄²⁻: O = -2, S: x +4*(-2) = -2 -> x = +6

CaSO₄: O = -2, S = +6, Ca = +2

E) PtCl₄: Cl = -1 (fixed), Pt: x + 4*(-1) = 0 -> x = +4

Cl⁻: Cl = -1

PtCl₆²⁻: Cl = -1, Pt = x + 6*(-1) = -2 -> x = +4

So, only in letter C Br₂ is undergoes both oxidation and reduction.

4 0

3 years ago

Which of the following will increase polymer strain to failure

Blizzard [7]

increase Polymer strain to failure is given below.

Explanation:

Strain to failure gives the measure of how much the specimen is elongated to failure. By this it means that, it you have strain to failure of 3% measured in specimen of length 100 mm, the material will fail when it it elongated 3 mm, as experimented in tensile test. Therefore, for a material with higher strain to failure rate, the ductility is higher and tensile strength is lower.

Tensile strength means the maximum mechanical stress (i.e. applied force divided by (initial) cross-section area of the specimen tested) during a tensile test, which is not directly correlated to the deformability or strain at failure or break since the tensile strength also is affected by the stiffness of the material. Therefore a ductile material might deform on a lower mechanical stress level than a stiffer one (this is the usual case), meaning its tensile strength is lower although its deformability is higher.

Therefore, for a material with higher strain to failure rate, the ductility is higher and tensile strength is lower.

4 0

4 years ago

which of these stars is least likely to be categorized as a supergiant? A. Betelgeuse B. Pollux C. Sirius A D. Sun Reset Submit

Vesna [10]

Answer: The correct answer is option D.

Explanation: Super-giant stars are the stars which are greater than Sun. They have a mass hundred time greater than Sun and can be thousand times greater than Sun.

The masses of the stars are represented in Solar masses which is the mass of the Sun.

Mass of Betelgeuse = 20 Solar masses

Mass of Pollux = 1.7 Solar masses

Mass of Sirius = 2.02 Solar masses

Mass of Sun = 1 Solar mass.

As, the mass of Sun is the least from the given stars. Hence, it is least considered as a super-giant.

5 0

4 years ago

if you have an isotope of the element carbon that has the mass number of 14, what other information would help you determine the

storchak [24]

Isotopes are forms of the same elements which contain equal number of protons but different number of nucleus in their nuclei, thus the differ in relative atomic mass but they have same chemical properties. The mass number is the summation of number of proton and number of neutron of an atom. If the mass number is known, then one need to know the number of proton in the atom in order to calculate for the number of neutron.

7 0

3 years ago