1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
Veronika [31]
3 years ago
7

It is acceptable to miss used absorbentes

Engineering
1 answer:
Flauer [41]3 years ago
4 0

Explanation:

I assume you meant mix instead of miss because the question wouldn't make sense otherwise.

I'd have to guess and say it is acceptable, because in order to comply with the used oil rule, a facility must properly manage its oil-contaminated sorbents (i.e., don't mix other wastes with these sorbents), and it must either recycle sorbents or send them for disposal at a permitted facility that burns them for energy recovery.

If this is incorrect, don't hesitate to report this answer.

You might be interested in
A 4-pole, 3-phase induction motor operates from a supply whose frequency is 60 Hz. calculate: 1- the speed at which the magnetic
DiKsa [7]

Answer:

The answer is below

Explanation:

1) The synchronous speed of an induction motor is the speed of the magnetic field of the stator. It is given by:

n_s=\frac{120f_s}{p}\\ Where\ p\ is \ the \ number\ of\ machine\ pole, f_s\ is\ the\ supply \ frequency\\and\ n_s\ is \ the \ synchronous\ speed(speed \ of\ stator\ magnetic \ field)\\Given: f_s=60\ Hz, p=4. Therefore\\\\n_s=\frac{120*60}{4}=1800\ rpm

2) The speed of the rotor is the motor speed. The slip is given by:

Slip=\frac{n_s-n_m}{n_s}. \\ n_m\ is\ the \ motor\ speed(rotor\ speed)\\Slip = 0.05, n_s= 1800\ rpm\\ \\0.05=\frac{1800-n_m}{1800}\\\\ 1800-n_m=90\\\\n_m=1800-90=1710\ rpm

3) The frequency of the rotor is given as:

f_r=slip*f_s\\f_r=0.04*60=2.4\ Hz

4) At standstill, the speed of the motor is 0, therefore the slip is 1.

The frequency of the rotor is given as:

f_r=slip*f_s\\f_r=1*60=60\ Hz

6 0
4 years ago
Can someone draw a electric circuit with electrical symbols for this
erastovalidia [21]

Answer:

i cant draw it

i am sry

Explanation:

4 0
3 years ago
Read 2 more answers
Supercharged engine what it does to the car
geniusboy [140]

Answer:

A supercharger is an air compressor that increases the pressure or density of air supplied to an internal combustion engine. This gives each intake cycle of the engine more oxygen, letting it burn more fuel and do more work, thus increasing power.

Explanation:

3 0
4 years ago
Read 2 more answers
Information such as tolerances and scale can be found in the _______________ of an engineering drawing.
nasty-shy [4]

Answer:

Information such as tolerance and scale can be found in the <u>title block</u> of an engineering drawing

Explanation:

The title block of an engineering drawing can normally be found on the lower right and corner of an engineering drawing and it carries the information that are used to specify details that are specific the drawing including, the name of the project, the name of the designer, the name of the client, the sheet number, the drawing tolerance, the scale, the issue date, and other relevant information, required to link the drawing with the actual structure or item

8 0
3 years ago
Discuss the environmental concerns regarding microfibre products
zlopas [31]

I don't know

Explanation:

cfffffffffggg

8 0
3 years ago
Other questions:
  • An ideal gas undergoes two processes: one frictionless and the other not. In both the cases, the gas is initially at 200 ℉ and 1
    7·2 answers
  • Two technicians are discussing solder wire repair. Technician A says that electrical tape can be used to cover the joint. Techni
    10·1 answer
  • A stream of air enters a 7.00-cm ID pipe at a velocity of 30.0 m/s at 27.0°C and 1.80 bar (gauge). At a point downstrream, the a
    15·1 answer
  • Water at 310 K and a flow rate of 4 kg/s enters an alumina tube (k=177Wm K1) with an inner diameter of 0.20 m and a wall thickne
    13·1 answer
  • WHAT IS THE MOST POWERFUL PART IN A CAR
    13·2 answers
  • Let CFG G be the following grammar.
    7·2 answers
  • Fill in the blank to correctly complete the statement below.
    6·1 answer
  • Planetary gears require the armature to be offset via a gear housing that holds the starter drive.
    12·2 answers
  • A red circle and diagonal slash on a sign means that:.
    10·1 answer
  • 1) Which step in the Design Process utilizes technical drawings to provide information necessary to
    8·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!