Ask question

Ask question

All categories

3 years ago

9

The fatigue data for a brass alloy are given as follows: Stress Amplitude (MPa) Cycles to Failure 170 3.7 × 104 148 1.0 × 105 13

0 3.0 × 105 114 1.0 × 106 92 1.0 × 107 80 1.0 × 108 74 1.0 × 109 i. Make an S–N plot (stress amplitude versus logarithm of cycles to failure) using these data. ii. Determine the fatigue strength at 4 × 106 cycles. iii. Determine the fatigue life for 120 MPa.

1 answer:

prohojiy [21]3 years ago

8 0

Answer:

i) S–N plot is attached

ii) fatigue strength = 100 MPa

iii) fatigue life = 5.62 x 10^(5) cycles

Explanation:

i) I have attached the S–N plot (stress amplitude versus logarithm of cycles to failure)

ii) The question says we should find the fatigue strength at 4 × 10^(6) cycles.

So let's find the log of this and trace it on the graph attached.

Log(4 × 10^(6)) = 6.6

From the graph attached, at log of cycle value of 6.6, the fatigue strength is approximately 100 MPa

iii) The question says we should find the fatigue life for 120 MPa.

Thus, from the graph, at stress amplitude of 120 MPa, the log of cycles is approximately 5.75.

Thus,the fatigue life will be the inverse log of 5.75.

Thus, fatigue life = 10^(5.75)

Fatigue life = 5.62 x 10^(5)

You might be interested in

An eddy current separator is to separate aluminum product from an input streamshredded MSW. The feed rate to the separator is 2,

blsea [12.9K]

Answer:

<em>the % recovery of aluminum product is 80.5%</em>

<em>the % purity of the aluminum product is 54.7%</em>

<em></em>

Explanation:

feed rate to separator = 2500 kg/hr

in one hour, there will be 2500 kg/hr x 1 hr = 2500 kg of material is fed into the machine

of this 2500 kg, the feed is known to contain 174 kg of aluminium and 2326 kg of rejects.

After the separation, 256 kg is collected in the product stream.

of this 256 kg, 140 kg is aluminium.

% recovery of aluminium will be = mass of aluminium in material collected in the product stream ÷ mass of aluminium contained in the feed material

% recovery of aluminium = 140kg/174kg x 100% = <em>80.5%</em>

% purity of the aluminium product = mass of aluminium in final product ÷ total mass of product collected in product stream

% purity of the aluminium product = 140kg/256kg

x 100% = <em>54.7%</em>

8 0

3 years ago

An inductor (L = 400 mH), a capacitor (C = 4.43 µF), and a resistor (R = 500 Ω) are connected in series. A 44.0-Hz AC generator

MakcuM [25]

Answer:

(A) Maximum voltage will be equal to 333.194 volt

(B) Current will be leading by an angle 54.70

Explanation:

We have given maximum current in the circuit $i_m=385mA=385\times 10^{-3}A=0.385A$

Inductance of the inductor $L=400mH=400\times 10^{-3}h=0.4H$

Capacitance $C=4.43\mu F=4.43\times 10^{-3}F$

Frequency is given f = 44 Hz

Resistance R = 500 ohm

Inductive reactance will be $x_l=\omega L=2\times 3.14\times 44\times 0.4=110.528ohm$

Capacitive reactance will be equal to $X_C=\frac{1}{\omega C}=\frac{1}{2\times 3.14\times 44\times 4.43\times 10^{-6}}=816.82ohm$

Impedance of the circuit will be $Z=\sqrt{R^2+(X_C-X_L)^2}=\sqrt{500^2+(816.92-110.52)^2}=865.44ohm$

So maximum voltage will be $\Delta V_{max}=0.385\times 865.44=333.194volt$

(B) Phase difference will be given as $\Phi =tan^{-1}\frac{X_C-X_L}{R}=\frac{816.92-110.52}{500}=54.70$

So current will be leading by an angle 54.70

5 0

3 years ago

What does STP and NTP stands for in temperature measurement?

Lisa [10]

STP stands for standard temperature pressure and NTP stands for normal temperature pressure

8 0

4 years ago

A 3.52 kg steel ball is tossed upward from a height of 6.93 meters above the floor with a vertical velocity of 2.99 m/s. What is

Dafna1 [17]

Answer : The final velocity of the ball is, 12.03 m/s

Explanation :

By the 3rd equation of motion,

$v^2-u^2=2as$

where,

s = distance covered by the object = 6.93 m

u = initial velocity = 2.99 m/s

v = final velocity = ?

a = acceleration = $9.8m/s^2$

Now put all the given values in the above equation, we get the final velocity of the ball.

$v^2-(2.99m/s)^2=2\times (9.8m/s^2)\times (6.93m)$

$v=12.03m/s$

Thus, the final velocity of the ball is, 12.03 m/s

7 0

3 years ago

What is the pressure at the bottom of a 25 ft volume of hydraulic fluid with a weight density of 55 lb/ft3 a. 114.6 psi b. 1375p

Assoli18 [71]

Answer:

d) 9.55 psi

Explanation:

pressure at the bottom is =ρgh

weight density is ρg=55 lb/ft³

h=25ft

pressure at the bottom is = $55\times 25$

=1375psf

1 ft = 12 inch

pressure at bottom = $\frac{1375}{12^2}$

= 9.55 psi

so, answer will be option (d) which is 9.55 psi

3 0

3 years ago