All categories

3 years ago

Which statement linking driving habits and fuel efficiency is true?

Engineering

1 answer:

Dafna11 [192]3 years ago

4 0

Answer: OC / THE 3 ANSWER

Explanation:

You might be interested in

Who ate cdonalds in hell with god then died from food ppoisoning

siniylev [52]

Answer:

McDonald’s announced recently that they are going through some major menu changes, and will be nixing some unnecessary ingredients. They also are finally listening to us, and will stop using chickens that are injected with growth-promoting antibiotics, along with dairy products raised with the growth hormone rbST but they still are using a lot of factory farmed meat and the beef is still raised with antibiotics.

McDonald’s even said they might add kale to their menu, by putting it in salads or in a smoothie. I LOVE kale, and I hope they don’t find a way to ruin it. You know the saying, “You can put lipstick on a pig, but it’s still a pig”. So, they need to do a lot more than just add kale to their menu before I’d ever eat there. The problem is that millions are still eating there and consuming several questionable food additives that McDonald’s could remove entirely if they really wanted to.

Explanation:

7 0

3 years ago

Five bolts are used in the connection between the axial member and the support. The ultimate shear strength of the bolts is 280

stiks02 [169]

Answer:

Minimum Allowable diameter for each of the 5 bolts = 0.0394 m = 3.94 cm

Explanation:

Maximum Working Stress = Ultimate Shear Stress/factor of safety

Maximum Working Stress = 280 MPa/3.8 = 73.68 MPa

Working Stress = Applied load/Minimum allowable Area = L/A

Minimum Allowable Area = Applied Load/Maximum Working Stress

A = 450000/73680000 = 0.00611 m²

This area is supplied by 5 bolts, so each bolt supplies A/5 = 0.0061/5 = 0.00122 m²

Cross sectional Area of bolts = πD²/4

0.00122 = πD²/4

D² = 4 × 0.00122/π = 0.00155

D = √0.00155 = 0.0394 m = 3.94 cm

Each of the five bolt can have a minimum diameter of 3.94 cm

Hope this Helps!!!

8 0

3 years ago

Three tool materials (high-speed steel, cemented carbide, and ceramic) are to be compared for the same turning operation on a ba

Tpy6a [65]

Answer:

Among all three tools, the ceramic tool is taking the least time for the production of a batch, however, machining from the HSS tool is taking the highest time.

Explanation:

The optimum cutting speed for the minimum cost

$V_{opt}= \frac{C}{\left[\left(T_c+\frac{C_e}{C_m}\right)\left(\frac{1}{n}-1\right)\right]^n}\;\cdots(i)$

Where,

C,n = Taylor equation parameters

$T_h$ =Tool changing time in minutes

$C_e$ =Cost per grinding per edge

$C_m$ = Machine and operator cost per minute

On comparing with the Taylor equation $VT^n=C$ ,

Tool life,

$T= \left[ \left(T_t+\frac{C_e}{C_m}\right)\left(\frac{1}{n}-1\right)\right]}\;\cdots(ii)$

Given that,

Cost of operator and machine time $=\$40/hr=\$0.667/min$

Batch setting time = 2 hr

Part handling time: $T_h=2.5$ min

Part diameter: $D=73 mm$ $=73\times 10^{-3} m$

Part length: $l=250 mm=250\times 10^{-3} m$

Feed: $f=0.30 mm/rev= 0.3\times 10^{-3} m/rev$

Depth of cut: $d=3.5 mm$

For the HSS tool:

Tool cost is $20 and it can be ground and reground 15 times and the grinding= $2/grind.

So, $C_e=$ $\$20/15+2=\$3.33/edge$

Tool changing time, $T_t=3$ min.

$C= 80 m/min$

$n=0.130$

(a) From equation (i), cutting speed for the minimum cost:

$V_{opt}= \frac {80}{\left[ \left(3+\frac{3.33}{0.667}\right)\left(\frac{1}{0.13}-1\right)\right]^{0.13}}$

$\Rightarrow 47.7$ m/min

(b) From equation (ii), the tool life,

$T=\left(3+\frac{3.33}{0.667}\right)\left(\frac{1}{0.13}-1\right)\right]}$

$\Rightarrow T=53.4$ min

(c) Cycle time: $T_c=T_h+T_m+\frac{T_t}{n_p}$

where,

$T_m=$ Machining time for one part

$n_p=$ Number of pieces cut in one tool life

$T_m= \frac{l}{fN}$ min, where $N=\frac{V_{opt}}{\pi D}$ is the rpm of the spindle.

$\Rightarrow T_m= \frac{\pi D l}{fV_{opt}}$

$\Rightarrow T_m=\frac{\pi \times 73 \times 250\times 10^{-6}}{0.3\times 10^{-3}\times 47.7}=4.01 min/pc$

So, the number of parts produced in one tool life

$n_p=\frac {T}{T_m}$

$\Rightarrow n_p=\frac {53.4}{4.01}=13.3$

Round it to the lower integer

$\Rightarrow n_p=13$

So, the cycle time

$T_c=2.5+4.01+\frac{3}{13}=6.74$ min/pc

(d) Cost per production unit:

$C_c= C_mT_c+\frac{C_e}{n_p}$

$\Rightarrow C_c=0.667\times6.74+\frac{3.33}{13}=\$4.75/pc$

(e) Total time to complete the batch= Sum of setup time and production time for one batch

$=2\times60+ {50\times 6.74}{50}=457 min=7.62 hr$ .

(f) The proportion of time spent actually cutting metal

$=\frac{50\times4.01}{457}=0.4387=43.87\%$

Now, for the cemented carbide tool:

Cost per edge,

$C_e=$ $\$8/6=\$1.33/edge$

Tool changing time, $T_t=1min$

$C= 650 m/min$

$n=0.30$

(a) Cutting speed for the minimum cost:

$V_{opt}= \frac {650}{\left[ \left(1+\frac{1.33}{0.667}\right)\left(\frac{1}{0.3}-1\right)\right]^{0.3}}=363m/min$ [from(i)]

(b) Tool life,

$T=\left[ \left(1+\frac{1.33}{0.667}\right)\left(\frac{1}{0.3}-1\right)\right]=7min$ [from(ii)]

(c) Cycle time:

$T_c=T_h+T_m+\frac{T_t}{n_p}$

$T_m= \frac{\pi D l}{fV_{opt}}$

$\Rightarrow T_m=\frac{\pi \times 73 \times 250\times 10^{-6}}{0.3\times 10^{-3}\times 363}=0.53min/pc$

$n_p=\frac {7}{0.53}=13.2$

$\Rightarrow n_p=13$ [ nearest lower integer]

So, the cycle time

$T_c=2.5+0.53+\frac{1}{13}=3.11 min/pc$

(d) Cost per production unit:

$C_c= C_mT_c+\frac{C_e}{n_p}$

$\Rightarrow C_c=0.667\times3.11+\frac{1.33}{13}=\$2.18/pc$

(e) Total time to complete the batch $=2\times60+ {50\times 3.11}{50}=275.5 min=4.59 hr$ .

(f) The proportion of time spent actually cutting metal

$=\frac{50\times0.53}{275.5}=0.0962=9.62\%$

Similarly, for the ceramic tool:

$C_e=$ $\$10/6=\$1.67/edge$

$T_t-1min$

$C= 3500 m/min$

$n=0.6$

(a) Cutting speed:

$V_{opt}= \frac {3500}{\left[ \left(1+\frac{1.67}{0.667}\right)\left(\frac{1}{0.6}-1\right)\right]^{0.6}}$

$\Rightarrow V_{opt}=2105 m/min$

(b) Tool life,

$T=\left[ \left(1+\frac{1.67}{0.667}\right)\left(\frac{1}{0.6}-1\right)\right]=2.33 min$

(c) Cycle time:

$T_c=T_h+T_m+\frac{T_t}{n_p}$

$\Rightarrow T_m=\frac{\pi \times 73 \times 250\times 10^{-6}}{0.3\times 10^{-3}\times 2105}=0.091 min/pc$

$n_p=\frac {2.33}{0.091}=25.6$

$\Rightarrow n_p=25 pc/tool\; life$

So,

$T_c=2.5+0.091+\frac{1}{25}=2.63 min/pc$

(d) Cost per production unit:

$C_c= C_mT_c+\frac{C_e}{n_p}$

$\Rightarrow C_c=0.667\times2.63+\frac{1.67}{25}=$1.82/pc$

(e) Total time to complete the batch

$=2\times60+ {50\times 2.63}=251.5 min=4.19 hr$ .

(f) The proportion of time spent actually cutting metal

$=\frac{50\times0.091}{251.5}=0.0181=1.81\%$

3 0

4 years ago

Aiman is 80 inches tall. How tall is Aiman in centimeters? Show your work.

harkovskaia [24]

203.2 centimeters.
This is because 1 inch = 2.54 centimeters which means multiply 80 inches X 2.54 = 203.2 centimeters.

5 0

2 years ago

When -iron is subjected to an atmosphere of hydrogen gas, the concentration of hydrogen in the iron, CH (in weight percent), is

djyliett [7]

Answer:

See attachments for step by step explanation towards getting answer.

Explanation:

Given that;

College Engineering 10+5 pts

When -iron is subjected to an atmosphere of hydrogen gas, the concentration of hydrogen in the iron, CH (in weight percent), is a function of hydrogen pressure, (in MPa), and absolute pH2temperature (T) according to(5.14)Furthermore, the values of D0 and Qd for this diffusion system are 1.4  10-7 m2/s and 13,400 J/mol, respectively. Consider a thin iron membrane 1 mm thick that is at 250C. Compute the diffusion flux through this membrane if the hydrogen pressure on one side of the membrane is 0.15 MPa (1.48 atm), and on the other side 7.5 MPa (74 atm).

See attachlent for complete solving.

6 0

3 years ago