Question 2) A material that is malleable can be defined as:

Direction: List down or enumerate the type of outlets you want to install on your dream house. Also indicate the quantity (in pi

Lorico [155]

Answer:

Apartment outlet 4pcs

Explanation:

6 0

3 years ago

Miller Indices:

svetlana [45]

Answer:

A) The sketches for the required planes were drawn in the first attachment [1 2 1] and the second attachment [1 2 -4].

B) The closest distance between planes are d₁₂₁=a/√6 and d₁₂₋₄=a/√21 with lattice constant a.

C) Five posible directions that electrons can move on the surface of a [1 0 0] silicon crystal are: |0 0 1|, |0 1 3|, |0 1 1|, |0 3 1| and |0 0 1|.

Compleated question:

1. Miller Indices:

a. Sketch (on separate plots) the (121) and (12-4) planes for a face centered cubic crystal structure.

b. What are the closest distances between planes (called d₁₂₁ and d₁₂₋₄)?

c. List five possible directions (using the Miller Indices) the electron can move on the surface of a (100) silicon crystal.

Explanation:

A)To draw a plane in a face centered cubic lattice, you have to follow these instructions:

1- the cube has 3 main directions called "a", "b" and "c" (as shown in the first attachment) and the planes has 3 main coeficients shown as [l m n]

2- The coordinates of that plane are written as: π:[1/a₀ 1/b₀ 1/c₀] (if one of the coordinates is 0, for example [1 1 0], c₀ is ∞, therefore that plane never cross the direction c).

3- Identify the points a₀, b₀, and c₀ at the plane that crosses this main directions and point them in the cubic cell.

4- Join the points.

In this case, for [1 2 1]:

$l=1=1/a_0 \rightarrow a_0=1$

$m=2=2/b_0 \rightarrow b_0=0.5$

$n=1=1/c_0 \rightarrow c_0=1$

for $[1 2 \overline{4}]$ :

$l=1=1/a_0 \rightarrow a_0=1$

$m=2=2/b_0 \rightarrow b_0=0.5$

$n=\overline{4}=-4/c_0 \rightarrow c_0=-0.25$

B) The closest distance between planes with the same Miller indices can be calculated as:

With $\pi:[l m n]$ ,the distance is $d_{lmn}= \displaystyle \frac{a}{\sqrt{l^2+m^2+n^2}}$ with lattice constant a.

In this case, for [1 2 1]:

$d_{121}= \displaystyle \frac{a}{\sqrt{1^2+2^2+1^2}}=\frac{a}{\sqrt{6}}=0.41a$

for $[1 2 \overline{4}]$ :

$d_{12\overline{4}}= \displaystyle \frac{a}{\sqrt{1^2+2^2+(-4)^2}}=\frac{a}{\sqrt{21}}=0.22a$

C) The possible directions that electrons can move on a surface of a crystallographic plane are the directions contain in that plane that point in the direction between nuclei. In a silicon crystal, an fcc structure, in the plane [1 0 0], we can point in the directions between the nuclei in the vertex (0 0 0) and e nuclei in each other vertex. Also, we can point in the direction between the nuclei in the vertex (0 0 0) and e nuclei in the center of the face of the adjacent crystals above and sideways. Therefore:

dir₁=|0 0 1|

dir₂=|0 0.5 1.5|≡|0 1 3|

dir₃=|0 1 1|

dir₄=|0 1.5 0.5|≡|0 3 1|

dir₅=|0 0 1|

5 0

3 years ago

Sort the following alphabets using MergeSort and give required steps. [2 Marks]

OlgaM077 [116]

Answer:

I'm afraid i can't visualise it to you but visit the site below to help you out <3

Explanation:

https://opendsa-server.cs.vt.edu/embed/mergesortAV

4 0

3 years ago

Does the Diesel engine have engine knock or detonation problem? Why?

Luda [366]

Explanation:

Yes Diesel engine have problem of knocking.

We know that knocking is phenomenon in which suddenly large amount of power generates this large amount of power will cause the failure of diesel engine.

Actually when one set of fuel inject inside the cylinder to burn with already compressed air (in general up to 10-15 bar) then this fuel does not burn complete and accumulate inside the cylinder.After that second set of fuel inject inside the cylinder then that one set of fuel burns with second set of fuel and produces large amount of sudden power for engine and causes the breaks in the crank or connecting rod of engine.it leads to damage the engine.

6 0

3 years ago

The process _______ boosted the production of fertilizers and strengthened the agriculture industry.

ANTONII [103]

Answer:

Process of Green Revolution

Explanation:

Green Revolution is a process which started its initiatives between the 1950s and 1960s, a technological research process, that increase agricultural productions through various systematic approach, which are different from the traditional methods. These technological approach includes:

1. Utilization of new varieties with a high yield potential, in addition with adequate water supply, pesticides and fertilizers.

2. New methods of cultivation and mechanization

Hence, the process of Green Revolution boosted production of fertilizers and strengthen the agriculture industry as a whole.

6 0

3 years ago