All categories

2 years ago

In third ange projection draw the plain view, front view and end view.

Engineering

1 answer:

Inessa [10]2 years ago

5 0

Answer:

The front view, is a drawing of the block, as if you are looking directly at the front of the object. The side view, is a drawing of the block, when it has been rotated so that one of its sides is now directly in view. The plan view, is a 'birds eye' view, from above.

You might be interested in

One who waits too long to complain has indicated satisfaction with the agreement despite the initial lack of true consent is the

katovenus [111]

Answer: Doctrine of ratification

Explanation:Doctrine of ratification tries to show that a person who is taking so much a time to complain has indicated that he agrees even if he doesn't without a written consent. This is to eliminate undue waste of time in business, legal an other proceedings requiring consent of both parties.

Doctrine of ratification can either be implied or expressed

Implied ratification is the type of ratification where a persons actions or body language can be seen that he has accepted.

Express ratification is a ratification where a person intentionally accept by showing either through written or verbally.

7 0

3 years ago

Consider a finite wing with an aspect of ratio of 7; the airfoil section of the wing is a symmetric airfoil with an infinite-win

kow [346]

Answer:

The solution for this question is attached below:

6 0

4 years ago

An isentropic steam turbine processes 2 kg/s of steam at 3 MPa, which is exhausted at50 kPa and 100C. Five percent of this flow

borishaifa [10]

Answer:

2285kw

Explanation:

since it is an isentropic process, we can conclude that it is a reversible adiabatic process. Hence the energy must be conserve i.e the total inflow of energy must be equal to the total outflow of energy.

Mathematically,

$\\ E_{inflow} = E_{outflow}$

Note: from the question we have only one source of inflow and two source of outflow (the exhaust at a pressure of 50kpa and the feedwater at a pressure of 5ookpa). Also the power produce is another source of outgoing energy $\\ E_{inflow} = m_{1} h_{1}$ .

$\\$

$E_{outflow} = m_{2} h_{2} + m_{3} h_{3} + W_{out}$

$\\$

Where $m_{1} h_{1}$ are the mass flow rate and the enthalpies at the inlet at a pressure of 3Mpa $\\$ ,

$m_{2} h_{2}$ are the mass flow rate and the enthalpies at the outlet 2 where we have a pressure of 500kpa respectively. $\\$ ,

and $m_{3} h_{3}$ are the mass flow rate and the enthalpies at the outlet 3 where we have a pressure of 50kpa respectively. $\\$ ,

We can now express write out the required equation by substituting the new expression for the energies $\\$

$m_{1} h_{1} = m_{2} h_{2} + m_{3} h_{3} + W_{out}$ $\\$

from the above equation, the unknown are the enthalpy values and the mass flow rate. $\\$

first let us determine the enthalpy values at the inlet and the out let using the Superheated water table. $\\$

It is more convenient to start from outlet 3 were we have a temperature $100^{0}C$ and pressure value of (50kpa or 0.05Mpa ). using double interpolation method on the superheated water table to determine the enthalpy value with careful calculation we have $\\$

$h_{3}$ = 2682.4 KJ/KG , at this point also from the table the entropy value , $s_{3}$ value is 7.6953 KJ/Kg.K. $\\$

Next we determine the enthalphy value at outlet 2. But in this case, we don't have a temperature value, hence we use the entrophy value since the entropy is constant at all inlet and outlet. $\\$

So, from the superheated water table again, at a pressure of 500kpa (0.5Mpa) and entropy value of 7.6953 KJ/Kg.K with careful interpolation we arrive at a enthalpy value of 3206.5KJ/Kg. $\\$

Finally for inlet one at a pressure of 3Mpa, interpolting with an entropy value of 7.6953KJ/Kg.K we arrive at enthalpy value of 3851.2KJ/Kg. $\\$

Now we determine the mass flow rate at each inlet and outlet. since mass must also be balance, i.e $m_{1} = m_{2} + m_{3}$ $\\$