1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
Andru [333]
3 years ago
9

A volleyball player hit a ball with a mass of 0.25 kg. The average acceleration of the ball was 15.5 m/s². How much force did th

e volleyball player apply to the ball? A. 3.87 m/s² B. 62.0 m/s² C. 3.87 N D. 62.0 N
Physics
2 answers:
iogann1982 [59]3 years ago
5 0
Force can be obtained by multiplying the mass of the object times the acceleration. Since all of the needed values are given, solving is done as shown below:

Force = mass x acceleration

Force = 0.25 kg x 15.5 m/s^2
Force = 3.875 N

Among the choices, the correct answer is C. 3.87 N
zhuklara [117]3 years ago
5 0

There must be movement for there to be work when a force is applied.

You might be interested in
The pressure and temperature at the beginning of compression of an air-standard Diesel cycle are 95 kPa and 300 K, respectively.
Liula [17]

Answer:

A.33.01

B.2.081

C.66%

Explanation:

See attached file pls

4 0
3 years ago
A 2.0 g identification reflector glued to one end of a helicopter rotor is spinning at a tangential velocity of 2093 m/s. The re
katrin2010 [14]
372863 juusnjus bhhhanbubhgajhus
7 0
3 years ago
It is estimated that 26 large pizzas are about right to serve 66 students of a physics club meeting. How many pizzas would be re
Brums [2.3K]

Answer:

The answer to your question is: 15 pizzas

Explanation:

data

26 large pizzas ------ 66 students

? large pizzas --------   38 students

Rule of three

x = 38 (26) / 66 = 14.96 ≈ 15 pizzas

5 0
3 years ago
The closeness of measured values to an accepted value is the BLANK of the data ?
wlad13 [49]
When you refer to how close a measured value is to a standard, accepted or known value, you are talking about the ACCURACY of the data. This is the definition of accuracy when it comes to engineering and other fields of science. 

Accuracy is usually associated or with the term precision, as their definitions are often interchanged.
3 0
3 years ago
As viewed from above in this picture, what direction will the current be in the coil of wire that will cause the loop to rotate
Gala2k [10]

Answer:

When viewed from above, the current in the coil should point towards the top-right corner of the picture.

Explanation:

The current in this coil have only two possible directions: clockwise or counter-clockwise. However, since the diagram shows the coil from above, not from a cross-section, just saying clockwise or counter-clockwise might be ambiguous. The statement that the current is directed towards the top-right corner of the picture is equivalent to saying that when viewed from the lower-right corner of this diagram, the current in the coil is moving clockwise.

Note that at the center of this picture, the current is parallel to the magnetic field- there will be no force on the coil at that position. On the other hand, (also when viewed from above,) at the top-right corner and the lower-left corner of the coil, the current in the coil will be perpendicular to the magnetic field. That's where the force on the coil will be the strongest.

With that in mind, apply the right-hand rule to find the direction of the force on the coil in each of the two possibilities.

Assume that when viewed from above, the current is flowing towards the top-right corner of the picture. Consider the wire near the top-right corner of this coil (as viewed above on this picture.) The current will be going into the picture into the magnetic field. By the right-hand rule, the current on the wire near that point should be pointing towards the bottom of this picture. (Point fingers on the right hand in the direction of the current I. Rotate the right hand such that when curling the fingers, they point in the direction of the magnetic field B. The direction of the right thumb should now point in the direction of the force on the wire F.)

Based on the same assumption, the current in the wires near the bottom left corner of this coil will be pointing out of the picture. By the right hand rule, the magnetic force on the coil in that region should be pointing towards the top of this picture. Combing these two forces, the coil would indeed be rotating around the center of this picture in the direction shown in the diagram.

It can also be shown that if the current points towards the bottom left corner of the picture when viewed from above, the coil will be rotating about the center of this picture in the opposite direction.

7 0
3 years ago
Other questions:
  • You run 100 meters in 15 seconds. What is your speed in m/s? and show your work
    13·1 answer
  • Assume an 8-kg bowling ball moving at 2m/s bounces off a spring at the same speed that it had before bouncing.What is the moment
    6·1 answer
  • A 72.0-kg object hits the ground at a velocity of 79.0 m/s. Neglecting air resistance, which relationship allows you to calculat
    9·1 answer
  • you and 3 friends apply a combined force of 489.5n to push a piano. The amount of work done is 1762.2j. What distance did the pi
    6·1 answer
  • What does co2 stand for
    10·2 answers
  • On Ramesh’s13th birthday, his father invited all his friends and their relatives. It was a big party with lots of food and DJs.
    11·1 answer
  • Determine the activity of the sample of cerium when the sample was 20 seconds old
    13·1 answer
  • An object travels 8 meters in the 1st second of travel, 8 meters again during the 2nd second of travel, and 8 meters again durin
    10·1 answer
  • Describe how water can be both physical and chemical weathering.
    13·1 answer
  • A vibrating mass of 300 kg mounted on a massless support by a spring of stiffness 40,000 N>m and a damper of unknown damping
    11·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!