1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
jok3333 [9.3K]
3 years ago
8

_____ life cycle models of systems development assume that the scope of the project can be articulated clearly and the schedule

and cost can be predicted accurately.
Physics
1 answer:
Natalka [10]3 years ago
4 0

Answer:

Predictive

Explanation:

 There is a wide variety of life cycles applicable to project management. In this regard, we currently have as a reference two somewhat extreme approaches that mark two very different ways of dealing with projects. The predictive approach and the agile approach.

  A predictive approach involves a great effort in initial planning and re-planning every time changes are accepted in the project. Therefore, this approach is recommended for changing but not highly changing environments. Although this approach is applicable to any type of project, clear examples of application would be the construction of a subway line, a bridge, the development of critical software. That is, projects where correct and detailed planting is key.

You might be interested in
Which Moon position in the lunar cycle would provide the largest difference in ocean tides?
nlexa [21]

The greatest difference between high and low tide is around New Moon and Full Moon. During these Moon phases, the solar tide coincides with the lunar tide because the Sun and the Moon are aligned with Earth, and their gravitational forces combine to pull the ocean's water in the same direction.

Your answer is B Full moon

5 0
2 years ago
To prevent dehydration when exercising on hot and humid days it is vital to:
Nostrana [21]
Drink water before, during, and after your exercise activity! i would rlly appreciate brainliest:D
8 0
3 years ago
Read 2 more answers
A Huge water tank is 2m above the ground if the water level on it is 4.9m high and a small opening is there at the bottom then t
lapo4ka [179]

Answer:

The speed of efflux of non-viscous water through the opening will be approximately 6.263 meters per second.

Explanation:

Let assume the existence of a line of current between the water tank and the ground and, hence, the absence of heat and work interactions throughout the system. If water is approximately at rest at water tank and at atmospheric pressure (P_{atm}), then speed of efflux of the non-viscous water is modelled after the Bernoulli's Principle:

P_{1} + \rho\cdot \frac{v_{1}^{2}}{2} + \rho\cdot g \cdot z_{1} = P_{2} + \rho\cdot \frac{v_{2}^{2}}{2} + \rho\cdot g \cdot z_{2}

Where:

P_{1}, P_{2} - Water total pressures inside the tank and at ground level, measured in pascals.

\rho - Water density, measured in kilograms per cubic meter.

g - Gravitational acceleration, measured in meters per square second.

v_{1}, v_{2} - Water speeds inside the tank and at the ground level, measured in meters per second.

z_{1}, z_{2} - Heights of the tank and ground level, measured in meters.

Given that P_{1} = P_{2} = P_{atm}, \rho = 1000\,\frac{kg}{m^{3}}, g = 9.807\,\frac{m}{s^{2}}, v_{1} = 0\,\frac{m}{s}, z_{1} = 6.9\,m and z_{2} = 4.9\,m, the expression is reduced to this:

\left(9.807\,\frac{m}{s^{2}} \right)\cdot (6.9\,m) = \frac{v_{2}^{2}}{2} + \left(9.807\,\frac{m}{s^{2}} \right)\cdot (4.9\,m)

And final speed is now calculated after clearing it:

v_{2} = \sqrt{2\cdot \left(9.807\,\frac{m}{s^{2}} \right)\cdot (6.9\,m-4.9\,m)}

v_{2} \approx 6.263\,\frac{m}{s}

The speed of efflux of non-viscous water through the opening will be approximately 6.263 meters per second.

5 0
4 years ago
HELP PLEASE!!
sweet-ann [11.9K]

Answer:

C. More of the heat is transferred to the kinetic energy of the copper atoms than to the kinetic energy of the water molecules.

Explanation:

Both equal masses of water and copper were heated at the same temperature. Since copper is a good conductor of heat compared to water, its  absorbs more heat. Which in-turn increases the rate of vibrations of the atoms in the copper mass, thus increasing their kinetic energy.

In the case of water, its molecules displaces one another after being heated to a higher temperature compared to neighboring molecules. So that the heated molecule becomes less dense and floats to the surface of water.

This property of copper makes it to be heated to a higher final temperature than the water.

6 0
3 years ago
If a 25jg car accelerates at a speed of 100 m/s^2, what will the force of the car be ?
Tema [17]
The answer is B............
6 0
3 years ago
Other questions:
  • Forces that are equal but oppistes are_____________ forces
    14·1 answer
  • During refraction, waves bend when they pass from one medium to another. The waves refract because their ________ changes. A) ap
    10·2 answers
  • One type of entrepreneurial business could be an online business, and the article
    5·2 answers
  • Will give Brainliest!! Question attached.
    5·2 answers
  • One end of a graphite rod is brought near a heat source. How does the other end of the rod eventually heat up? A. Directly from
    6·1 answer
  • A car of mass 1600 kg traveling at 27.0 m/s is at the foot of a hill that rises vertically 135 m after travelling a distance of
    12·1 answer
  • WHAT FEATURE DO ALL VOLCANOES SHARE? PLEASE LIST AT LEAST 3!!!
    12·2 answers
  • In projectile mtion, what is the y-component of the initial velocity? if V= Vi = 100 m/s and the angle with horizontal axis Θ =
    14·2 answers
  • Please help me with this (with explanation)
    6·1 answer
  • Question 5 of 5<br> What do the arrows in the photograph represent?
    8·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!