1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
ch4aika [34]
3 years ago
7

The TSS concentration in the primary treated effluent is 150 mg/L, and TSS removal is 63 percent. The sludge has an average soli

ds concentration of 6 percent and specific gravity of 1.045. What is the capacity of the sludge pump in m3/min per basin if the pump is used on a 15-min pumping cycle per h

Engineering
1 answer:
Umnica [9.8K]3 years ago
7 0

Answer:

The capacity of the sludge pump is 0.217 m3/min

Explanation:

Solution is attached below

You might be interested in
. Air at 200 C blows over a 50 cm x 75 cm plain carbon steel (AISI 1010) hot plate with a constant surface temperature of 2500 C
MrRissso [65]

Answer:

The inside temperature, T_{in} is approximately 248 °C.

Explanation:

The parameters given are;

Temperature of the air = 20°C

Carbon steel surface temperature 250°C

Area of surface = 50 cm × 75 cm = 0.5 × 0.75 = 0.375 m²

Convection heat transfer coefficient = 25 W/(m²·K)

Heat lost by radiation = 300 W

Assumption,

Air temperature = 20 °C

Hot plate temperature = 250 °C

Thermal conductivity K = 65.2 W/(m·K)

Steady state heat transfer process

One dimensional heat conduction

We have;

Newton's law of cooling;

q = h×A×(T_s - T_{\infty) + Heat loss by radiation

= 25×0.325×(250 - 20) + 300

= 2456.25 W

The rate of energy transfer per second is given by the following relation;

P = \dfrac{K \times A \times \Delta T}{L}

Thermal conductivity K = 65.2 W/(m·K)

Therefore;

2456.25  = \dfrac{65.2 \times 0.375 \times (250 - T_{in})}{0.02}

T_{in} = 250 - \dfrac{2456.25  \times 0.02}{65.2 \times 0.375} = 247.99 ^{\circ}C

The inside temperature, T_{in} = 247.99 °C  ≈ 248 °C.

3 0
3 years ago
A plate of an alloy steel has a plane-strain fracture toughness of 50 MPa√m. If it is known that the largest surface crack is 0.
Ivahew [28]

Answer:

option B is correct. Fracture will definitely not occur

Explanation:

The formula for fracture toughness is given by;

K_ic = σY√πa

Where,

σ is the applied stress

Y is the dimensionless parameter

a is the crack length.

Let's make σ the subject

So,

σ = [K_ic/Y√πa]

Plugging in the relevant values;

σ = [50/(1.1√π*(0.5 x 10^(-3))]

σ = 1147 MPa

Thus, the material can withstand a stress of 1147 MPa

So, if tensile stress of 1000 MPa is applied, fracture will not occur because the material can withstand a higher stress of 1147 MPa before it fractures. So option B is correct.

8 0
3 years ago
Robomind academy code if hour
Anvisha [2.4K]
Erm what? ......;-;
7 0
3 years ago
A group of n Ghostbusters is battling n ghosts. Each Ghostbuster carries a proton pack, which shoots a stream at a ghost, eradic
babunello [35]

Answer:

Using the above algorithm matches one pair of Ghostbuster and Ghost. On  each side of the line formed by the pairing, the number of Ghostbusters and Ghosts are  the same, so use the algorithm recursively on each side of the line to find pairings. The  worst case is when, after each iteration, one side of the line contains no Ghostbusters  or Ghosts. Then, we need n/2 total iterations to find pairings, giving us an P(n^{2} lg n)-  time algorithm.

4 0
3 years ago
Based on the graphs of stress-strain from the V-MSE site, how would you characterize the general differences between polymers an
Pepsi [2]

Answer:

Option A

Explanation:

Alloys are metal compounds with two or more metals or non metals to create new compounds that exhibit superior structural properties. Alloys have high level of hardness that resists deformation thereby making it less ductile compared to polymers. This is due to the varying difference in the chemical and physical characteristics of the constituent metals in the alloy.

6 0
3 years ago
Other questions:
  • Anyone have any good ways of revisiting <br> Or <br> Have any good study notes
    11·1 answer
  • Which of the following is not a primary or fundamental dimension? (a)-mass m (b)-length L (c)- timer t (d)-volume V
    5·1 answer
  • A milling operation was used to remove a portion of a solid bar of square cross section. Forces of magnitude P = 18 kN are appli
    15·1 answer
  • Alberto's mom is taking a splinter out of his hand with a pair of tweezers. The tweezers are 3 inches long. She is applying .25
    12·2 answers
  • if you had 100 B size sheets and you cut them into A size sheets, how many sheets of A size paper would you have
    14·1 answer
  • The attached program (studentsGpa.cpp) uses dynamic allocation to create an array of strings. It asks the user to enter a number
    10·1 answer
  • In a flow over a flat plate, the Stanton number is 0.005: What is the approximate friction factor for this flow a)- 0.01 b)- 0.0
    8·1 answer
  • What is the maximum fine for knowingly refilling a disposable refrigerant drum?
    11·1 answer
  • Hey answer quick for 20 points
    7·2 answers
  • This test should be performed on all cord sets, receptacles that aren't part of a building or structure's permanent wiring, and
    5·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!