Is the LED an actuator?

Which of these cars traveled faster during time interval <br> please show solution

Mazyrski [523]

Answer:

I think D is correct

Explanation:

C is decreasing function, probably worst

A is arctan -> in radian, the rate of increasing is very slow-> second worst

B(14) = ln(9*14) = 4.8

D(14) = sqrt(8+14^2)=14.2

3 0

3 years ago

Write the following statements as Prolog clauses, in the order given: If it is raining or snowing, then there is precipitation.

Anika [276]

Answer:

a. See Explanation Below

b. No

Explanation:

a.

Interpreting the statements line by line.

First, the prolog clauses need to be initialised, as follows:

:- dynamic freezing/0, precipitation/0, snowing/0, raining/0.

If it is raining or snowing, then there is precipitation.

The statement is splited in two.

1st, if it is raining then there is precipitation

Or

2nd, if it is raining, then there is precipitation.

So, both statements are given as:

precipitation :- raining.

precipitation :- snowing.

If it is freezing and there is precipitation, then it is snowing.

This is a conditional statement that checks if it is freezing AND there's is precipitation.

If true, then it is snowing.

The above statement is given as:

snowing :- freezing, precipitation.

If it is not freezing and there is precipitation, then it is raining.

This is a conditional statement that checks if it is not freezing AND there's is precipitation.

If true, then it is raining.

The not clause is represented as \+

The above statement is the given as:

raining :- \+ freezing, precipitation.

It is snowing.

This is represented as follows

snowing.

So, the full prolog clause is as follows

:- dynamic freezing/0, precipitation/0, snowing/0, raining/0.

precipitation :- raining.

precipitation :- snowing.

snowing :- freezing, precipitation.

raining :- \+ freezing, precipitation.

snowing.

b. What answer does Prolog give to the following queries:

Is it freezing

No

Reason;

All of the conditions above point to raining or snowing; none points to freezing.

Hence, it is no.

8 0

3 years ago

Air enters the combustor of a jet engine at p1=10 atm, T1=1000°R, and M1=0.2. Fuel is injected and burned, with a fuel/air mass

snow_lady [41]

Answer:

M2 = 0.06404

P2 = 2.273

T2 = 5806.45°R

Explanation:

Given that p1 = 10atm, T1 = 1000R, M1 = 0.2.

Therefore from Steam Table, Po1 = (1.028)*(10) = 10.28 atm,

To1 = (1.008)*(1000) = 1008 ºR

R = 1716 ft-lb/slug-ºR cp= 6006 ft-lb/slug-ºR fuel-air ratio (by mass)

F/A =???? = FA slugf/slugaq = 4.5 x 108ft-lb/slugfx FA slugf/sluga = (4.5 x 108)FA ft-lb/sluga

For the air q = cp(To2– To1)

(Exit flow – inlet flow) – choked flow is assumed For M1= 0.2

Table A.3 of steam table gives P/P* = 2.273,

T/T* = 0.2066,

To/To* = 0.1736 To* = To2= To/0.1736 = 1008/0.1736 = 5806.45 ºR Gives q = cp(To* - To) = (6006 ft-lb/sluga-ºR)*(5806.45 – 1008)ºR = 28819500 ft-lb/slugaSetting equal to equation 1 above gives 28819500 ft-lb/sluga= FA*(4.5 x 108) ft-lb/slugaFA =

F/A = 0.06404 slugf/slugaor less to prevent choked flow at the exit

5 0

3 years ago

What will happen in a wire drawing operation when the cross-sectional area has a reduction of 60% in a single pass?

Fofino [41]

Answer:

DRAWING LOAD IS $3.67 A_{O}\sigma$

Explanation:

wire drawing is a method of obtaining wire of bigger large diameter from iron rod . it is cold process which need die to obtain wire

drawing load for wire drawing is given as P = $A_{F}*\sigma*ln(\frac{A_{O}}{A_{F}})$

Where A f is initial area, Ao is original area, σ is yield stress

as given in question sectional area reduce 60%, therefore

$A_{f} = A_{O}- 0.6A_{O}$

= $0.4 A_{O}$

Due to change in area ,drawing load p is

p = $0.4A_{O}*\sigma*ln(\frac{A_{O}}{0.4A_{O}})$

p = $3.67 A_{O}\sigma$

4 0

3 years ago

While at a concert you notice five people in the crowd headed in the same direction. Your tendency to group them is due to? *

Vlada [557]

Answer:

common fate

Explanation:

The gestalt effect may be defined as the ability of our brain to generate the whole forms from the groupings of lines, points, curves and shapes. Gestalt theory lays emphasis on the fact that whole of anything is much greater than the parts.

Some of the principles of Gestalt theory are proximity, similarity, closure, symmetry & order, figure or ground and common fate.

Common fate : According to this principle, people will tend to group things together which are pointed towards or moving in a same direction. It is the perception of the people that objects moving together belongs together.

7 0

3 years ago