1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
ddd [48]
3 years ago
13

What is the safe psi pressure for acetylene

Engineering
1 answer:
Simora [160]3 years ago
4 0

Answer:

15psig

Explanation:

You might be interested in
If you were to plot the voltage versus the current for a given circuit, what would you expect the slope of the line to be? If no
Brut [27]

Answer:

Part 1: It would be a straight line, current will be directly proportional to the voltage.

Part 2: The current would taper off and will have negligible increase after the voltage  reaches a certain  value. Graph attached.

Explanation:

For the first part, voltage and current have a linear relationship as dictated by the Ohm's law.

V=I*R

where V is the voltage, I is the current, and R is the resistance. As the Voltage increase, current is bound to increase too, given that the resistance remains constant.

In the second part, resistance is not constant. As an element heats up, it consumes more current because the free sea of electrons inside are moving more rapidly, disrupting the flow of charge. So, as the voltage increase, the current does increase, but so does the resistance. Leaving less room for the current to increase. This rise in temperature is shown in the graph attached, as current tapers.

7 0
4 years ago
A disk of radius 2.1 cm has a surface charge density of 5.6 µC/m2 on its upper face. What is the magnitude of the electric field
Assoli18 [71]

Answer:

=6.3*10^3 N/C

Explanation:

solution:

from this below equation (1)

E=σ/2εo(1-\frac{z}{\sqrt{z^2-R^2} } )...........(1)

we obtain:

=5.6*10^-6 \frac{c}{m^2} /2(8.85*10^-12\frac{c^2}{N.m^2} ).(1-\frac{9.5 cm}{\sqrt{9.5^2-2.1^2} } )

=6.3*10^3 N/C

8 0
3 years ago
Hogden is conducting an experiment to determine how much force it takes for a nail to puncture a tire, causing a flat. He uses f
SashulF [63]

Answer:

B

Explanation:

8 0
3 years ago
Read 2 more answers
Which of the following bonding is the strongest? (a) lonic bonding (b) Metallic bonding (c) Covalent bonding with some van der W
OLEGan [10]

Answer:

(a) lonic bonding

Explanation:

The Strongest chemical bond is the ionic bond ,

Because ionic bond is bound by strong electrostatic interactions ,

The ionic bond forms crystal lattice structure which are bounded by  electrostatic interactions but the covalent bond is formed by the van der waal forces .

Hence , ionic bond is stronger than covalent bond .

7 0
3 years ago
If a 2 1/8 inch diameter medium carbon steel rod is to be turned between centers to a 2 inch diameter using high speed cutting b
Crank

Answer:

I think 1 31/32

8 0
4 years ago
Other questions:
  • Water vapor at 6 MPa, 500°C enters a turbine operating at steady state and expands to 20 kPa. The mass flow rate is 3 kg/s, and
    8·1 answer
  • What is the air change rate (ACH) for a 100 ft^2 (9.3 m^2) space with a 10 ft (3.0 m) ceiling and an airflow rate of 200 cfm (95
    12·1 answer
  • Find the mass if the force is 18 N and the acceleration is 2 m/s2
    8·2 answers
  • A _____ satellite system employs many satellites that are spaced so that, from any point on the Earth at any time, at least one
    10·1 answer
  • Convert mechanical energy into electric energy. What can he use?
    13·1 answer
  • Your manager has asked you to research and recommend a writing guide that examiners in your digital forensics company can use fo
    8·1 answer
  • A car is traveling at 50 ft/s when the driver notices a stop sign 100 ft ahead and steps on the brake. Assuming that the deceler
    6·1 answer
  • An op-amp differential amplifier is built using four identical resistors, each having a tolerance of ±5%. Calculate the worst p
    14·1 answer
  • What building codes did Mega Corporation fail to follow?
    9·1 answer
  • Which level of acceleration should you use when accelerating on a short highway entry ramp?
    11·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!