1answer.
Ask question
Login Signup
Ask question
All categories
  • English
  • Mathematics
  • Social Studies
  • Business
  • History
  • Health
  • Geography
  • Biology
  • Physics
  • Chemistry
  • Computers and Technology
  • Arts
  • World Languages
  • Spanish
  • French
  • German
  • Advanced Placement (AP)
  • SAT
  • Medicine
  • Law
  • Engineering
fgiga [73]
2 years ago
10

According to the EPA Lead and Copper Rule (LCR), the action level for Pb in drinking water (the level at which threat to human h

ealth requires public notification and action towards mitigation) is 15 ppb. If you were to add enough phosphate to the system
saturated with respect to Pb3(PO4)2(s), would the [Pb2+] be below the action limit?
Chemistry
1 answer:
steposvetlana [31]2 years ago
7 0

Answer:

The right answer is "105.17 ppb".

Explanation:

According to the question,

The amount of Pb^{2+} in ppb will be:

= 0.5076\times 10^{-6}\times 207.2\times  106

= 105.17 \ ppb

Thus, the amount of Pb^{2+} is above action limit.

You might be interested in
Which phase change results in atoms with the highest kinetic energy? A. Boiling B. Melting C. Freezing D. Condensing
suter [353]

Answer: Boiling because it makes the molecules in water bounce around.

Hope it helps.

4 0
3 years ago
URGENT
antoniya [11.8K]

Answer:

a

Explanation:

8 0
3 years ago
Given the reaction:
tino4ka555 [31]

4 moles of NaCl is produced from 2 moles of Na₂CrO₄.

<u>Explanation:</u>

Given reaction is

PbCl₂(aq) + Na₂CrO₄(aq)→ PbCrO₄(s) + 2 NaCl (aq)

It is the balanced equation which means that on both sides of the equation, number of atoms of each element are equal.

From the above balanced equation it says that molar ratio of Na₂CrO₄ to NaCl is 1 : 2.

That is 1 mole of Na₂CrO₄ produces 2 moles of NaCl, so the molar ratio is 1:2.

2 moles of Na₂CrO₄  produces 4 moles of NaCl.

So the molar ratio of Na₂CrO₄ to NaCl is 2: 4.

6 0
3 years ago
The following questions pertain to a system contains 122 g CO(g) in a 0.400 L container at -71.2 degrees C.
7nadin3 [17]

Answer:

a. P = 182 atm

Explanation:

Data Given:

amount of CO = 122g

Volume of CO = .400 L

Temperature of CO =  -71.2°C

Convert the temperature to Kelvin

T = °C + 273

T =  -71.2 + 273

T =  201.8 K

a. Calculate the pressure exerted by the CO(g) in this system using the ideal gas equation (P) = ?

Solution:

To calculate Pressure by using ideal gas formula

                  PV = nRT

Rearrange the equation for Pressure

                   P = nRT / V . . . . . . . . . (1)

where

P = pressure

V = Volume

T= Temperature

n = Number of moles

R = ideal gas constant = 0.08206 L.atm / mol. K

For this we have to know the mole of the gas and the following formula will be used

                 no. of moles = mass in grams / molar mass . . . . . . (2)

Molar mass of CO = 12 + 16 = 28 g/mol

Put values in equation 2

                no. of moles = 122 g / 28 g/mol

                no. of moles = 4.4 mol

Now put the value in formula (1) to calculate Pressure for CO

P = 4.4 x 201.8 K x 0.08206 (L.atm/mol. K) / 0.400 L

P = 182 atm

So the pressure will be 182 atm

__________

b. Data Given:

Actual pressure exerted by CO = 145 atm

expected pressure exerted by CO = 182 atm

why the actual pressure is less than what would be expected = ?

Explanation:

This is because of the deviation from ideal behavior of real gases.

The real gases approach to ideal behavior under very high temperature and very low pressure.

But CO deviate from ideal behavior to give expected value for pressure, because it behave at high pressure and low temperature.

This non-ideal behavior is due to two postulate of ideal behavior

  • gas molecules have negligible volume
  • Gas molecules have negligible inter-molecular interaction

but these postulates not obeyed under real condition. so we calculated the pressure using ideal condition values for gas and obtained the expected value for pressure but the actual pressure value was detected under normal condition.

8 0
3 years ago
What does initial buret and final buret reading mean
ikadub [295]
Initial buret reading means the volume of acid taken in the buret and final reading means the remaining volume of acid after experiment
 
4 0
3 years ago
Other questions:
  • Which of he following compounds is always part of an aqueous solution
    6·1 answer
  • Science question down below
    14·1 answer
  • 1 Which scientist first said that "elements are made up of identical atoms
    8·1 answer
  • Number 41? Need help how do you get answrb
    10·1 answer
  • Use the periodic table to answer the questions below.
    9·2 answers
  • Suppose you are investigating the reaction: M(s) + 2 HCl(aq) → MCl2(aq) + H2(g). You weigh out a 0.295 gram piece of metal and c
    15·1 answer
  • A family takes a summer vacation to Florida. They drive for 8 hours before stopping at a hotel for the night. They
    11·1 answer
  • Two chemicals A and B are combined to form a chemical C. The rate, or velocity, of the reaction is proportional to the product o
    6·1 answer
  • 6. A box measures 11.25 inches in length, 8.1 inches in width and 6.85 inches in height. What is the
    5·1 answer
  • What would be the mass in grams of 0.300 moles of the ionic compound formed when magnesium metal reacts with oxygen
    11·1 answer
Add answer
Login
Not registered? Fast signup
Signup
Login Signup
Ask question!