All categories

3 years ago

A series RC circuit has a voltage of 24VAC and an impedance of 252ohms. What is the circuit current?

Engineering

1 answer:

Mumz [18]3 years ago

5 0

Answer:

the current in the circuit is 95.2 mA.

Explanation:

Given;

voltage in the circuit, V = 24 V

impedance of the circuit components, Z = 252 ohms

The current in the circuit is calculated as;

$I = \frac{V}{Z} \\\\I = \frac{24}{252} \\\\I = 0.0952 \ A\\\\I = 95.2 \ mA$

Therefore, the current in the circuit is 95.2 mA.

You might be interested in

Component of earthing and reasons why each material is being used<br><br>

timofeeve [1]

Answer:

The components of earthing are Earth electrode, Main earthing terminals/bars, Earthing conductors, Protective conductors Equipontential binding conductors and Electrically independent electrodes.

3 0

2 years ago

4. Two technicians are discussing the evaporative emission monitor. Technician A says that serious monitor faults cause a blinki

snow_lady [41]

Answer:

The correct option is;

Neither Technician A nor B

Explanation:

The evaporative emission monitor or Evaporaive Emission Control System EVAP System monitors enables the Power Control Module of the car to check fuel system leak integrity and the vapor consumption efficiency during engine combustion

It is a requirement of EPA on cars to check the emission of smug forming evaporates from cars

Serious monitor faults can cause the turning on of the check engine lights and the vehicle will not pass OBD II test, but it will not lead to engine shutdown

It runs when the engine is 15 to 85% full and the TP sensor is between 9% and 35%.

Therefore, the correct option is that neither Technician A nor B are correct.

3 0

3 years ago

1 A power transmission includes a belt drive, a chain drive and a gear drive. Which of the following is the best arrangement bet

Setler79 [48]

Answer:d

Explanation:

(d) chain drive belt drive gear drive

3 0

3 years ago

A sleeve made of SAE 4150 annealed steel has a nominal inside diameter of 3.0 inches and an outside diameter of 4.0 inches. It i

irga5000 [103]

Answer:

Class of fit:

Interference (Medium Drive Force Fits constitute a special type of Interference Fits and these are the tightest fits where accuracy is important).

Here minimum shaft diameter will be greater than the maximum hole diameter.

Medium Drive Force Fits are FN 2 Fits.

As per standard ANSI B4.1 :

Desired Tolerance: FN 2

Tolerance TZone: H7S6

Max Shaft Diameter: 3.0029

Min Shaft Diameter: 3.0022

Max Hole Diameter:3.0012

Min Hole Diameter: 3.0000

Max Interference: 0.0029

Min Interference: 0.0010

Stress in the shaft and sleeve can be considered as the compressive stress which can be determined using load/interference area.

Design is acceptable If compressive stress induced due to selected dimensions and load is less than compressive strength of the material.

Explanation:

4 0

3 years ago

Read 2 more answers

Which traits are common in all four career pathways of the Information Technology field? Check all that apply.

Komok [63]

Answer:

Accuracy and attention to detail, Problem solving and critical thinking skills, Knowledge of programming language .

Explanation:

It is a technological area in which a person learns how to develop computer hardware, including PCs, laptops, tablets, processing, networking, and other hardware parts. Another field of study in IT is Management Information Systems (MIS).

The IT industry's career paths can be categorized equally in the two primary field’s hardware and software areas

In hardware, there is Production, maintenance, research and development, and strategic planning.

In software, there is manufacturing, development, programming, software testing, and maintenance and support under software.

Computer operations, administration of databases, sales / marketing and data centre management are connected areas.

7 0

2 years ago